manualshive.com logo in svg

ATEN CS1308, User Manual

The ATEN CS1308 is a top-notch switch with advanced features and user-friendly design. To maximize its potential, make sure to refer to the comprehensive User Manual, available for free download at manualshive.com. This manual is essential for setting up and optimizing your ATEN CS1308 switch efficiently and hassle-free.

Share
Download
background image

CS1308 / CS1316 User Manual

42

Preparation

To prepare for the firmware upgrade, do the following:

1. Use the 

Firmware Upgrade Cable

 provided with this unit to connect a COM 

port on your computer to the 

Firmware Upgrade Port

 of your switch.

2. Shut down all the computers on the KVM installation.

3. From your KVM switch console, login to the OSD as the administrator 

(see p. 19) and select the 

F4 ADM

 function.

4. Scroll down to FIRMWARE UPGRADE. Press 

[Enter]

, then press 

[Y]

 to 

invoke 

Firmware Upgrade

 mode (see p. 27.)

Summary of Contents for CS1308





































































Reviews:

No comments

Related manuals for CS1308

CALIENT S320 Repair And Diagnostics Field Manual preview
S320
Brand: CALIENT Pages: 22
Aastra CNX Release Note preview
CNX
Brand: Aastra Pages: 12
Aastra CNX Quick Reference Card preview
CNX
Brand: Aastra Pages: 2
Kathrein EXE 159 Manual preview
EXE 159
Brand: Kathrein Pages: 41
S&C Omni-Rupter Installation Manual preview
Omni-Rupter
Brand: S&C Pages: 28
S&C Mark V Assembly And Installation Instructions Manual preview
Mark V
Brand: S&C Pages: 12
S&C Alduti-Rupter Instruction Sheet preview
Alduti-Rupter
Brand: S&C Pages: 24
S&C Alduti-Rupter Additional Instructions For Installation And Operation preview
Alduti-Rupter
Brand: S&C Pages: 24
S&C Vista SD Instruction Sheet preview
Vista SD
Brand: S&C Pages: 24
S&C Alduti-Rupter Installation Manual preview
Alduti-Rupter
Brand: S&C Pages: 28
S&C Vista SD Operation Manual preview
Vista SD
Brand: S&C Pages: 37
Valcom V-2972 User Manual preview
V-2972
Brand: Valcom Pages: 2
D-Link DES-3224 - Switch User Manual preview
DES-3224 - Switch
Brand: D-Link Pages: 75
3onedata TNS5800-8GP16GT-P24VDC Quick Installation Manual preview
TNS5800-8GP16GT-P24VDC
Brand: 3onedata Pages: 3
IOGear GCS62DP Quick Start Manual preview
GCS62DP
Brand: IOGear Pages: 10
TAXON TOOLS Scart Switch Manual preview
Scart Switch
Brand: TAXON TOOLS Pages: 9
Abseco AFI-2M0S1B Installation Manual preview
AFI-2M0S1B
Brand: Abseco Pages: 10
Lakeshore 3f Delta Operation & Maintenance Manual preview
3f Delta
Brand: Lakeshore Pages: 82

Brands by name

Popular brands

Load more brands