AT&T OneVision DEFINITY G3 Guide Installation And Connection Manual Download Page 135

Page: 135 / 287

Issue 2 April 1996

6-21

Connectivity
To Configure Data Modules

To Configure Data
Modules

When to use

Configure your 7400B data module after it is installed.

You do not need to complete the following procedures if you
installed ADU or PDM data modules.

Procedural
overview

The following procedures configure the 7400B data module:

■

Procedure 1: Ad d the tty device name

■

Procedure 2: Set data module options

Procedure 1:
Add the tty
device name

Use the following steps to ad d the tty device name to the Devices
file.

Summary of Contents for OneVision DEFINITY G3 Guide
































































































































































































































































































Search results

Summary of Contents for OneVision DEFINITY G3 Guide

Reviews:

AT&T OneVision DEFINITY G3 Guide, Installation And Connection Manual, Page: 135 / 287

Search results

Summary of Contents for OneVision DEFINITY G3 Guide

Reviews: