ASV PT-80 Operation And Maintenance Manual Download Page 52 | Manualshive

Page: 52 / 72

background image

Track Tension (PT-70/80)

Proper track tension must be
maintained for optimal perform-
ance and track/undercarriage
life. Running a track that is too
loose may cause the track to
misfeed possibly causing dam-
age to the track and or under-
carriage components. Running
a track that is too tight may
cause track stretch, premature
bearing failure, or other prevent-
able damage to the machine. As
a rule, a track should only be
tightened to the point where
there is no visible sag. Never
tighten your tracks beyond this
point.

Note:

During the first 50 hours

of operation the tracks will
"break-in" and will most likely
require adjustment.

To check track tension: (fig. 1, 2)

1.

Drive the machine forward 5
feet to remove belt slack
from the lower and rearward
portions of the track.

2.

Lay a straight edge along
the top of the track bridging
the drive sprocket and front
idler wheel.

3.

Apply 90 lbs. of down force
to the the track by either
placing weight on top or
hanging it using rope or wire
midway between the drive
sprocket and front idler.

4.

Measure from the bottom of
the straight edge to the lug
surface (top) of the track.
The deflection should meas-
ure between 3/4" and 1".

To adjust track tension: (fig. 3)

1.

Loosen the lock nut (A) on
the turnbuckle (B) and
adjust by turning the turn
buckle itself until proper ten-
sion has been achieved.

2.

Then tighten the turnbuckle
lock nut to complete the
procedure.

3.

Repeat the adjustment pro-
cedure on the other side of
the machine if necessary.

MAINTENANCE

Undercarriages

51

1

2

Straight-Edge

3

A

B

«
...
50
51
52
53
54
...
»

Summary of Contents for PT-80









































































Reviews:

No comments

Related manuals for PT-80

Brand: Case Pages: 22

Brand: Mertz Pages: 84

Brand: Terex Pages: 218

Brand: RHINO Pages: 56

Brand: Noblelift Pages: 107

Brand: Bush Hog Pages: 42

Brand: Bush Hog Pages: 102

Brand: Bush Hog Pages: 106

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands