Asus WL-106gM User Manual Download

Page: 7 / 39

ASUS WLAN Card

Chapter 2 - Installation

Chapter 2 Installation

2. Installation

System Requirements

To begin using the WLAN Card, you must meet the following minimum

requirements:

• Windows XP/2000

• Standard PCMCIA slot Type II or Type III for notebook computer

• 128MB system memory or larger

• 750MHz processor or higher

Important: Install the WLAN card utilities before inserting the WLAN Card

into your computer.

Installing the WLAN utilities and driver

Follow these instructions to install the WLAN card utilities and driver. Insert the

support CD into your optical drive. If autorun is enabled in your computer, the

CD automatically displays the utility menu. Click

Install ASUS WLAN Card

Utilities/Driver

. If autorun is disabled, double-click SETUP.EXE in the root

directory of the CD.

2. Click

Next

on the Welcome screen.

1. Select your language and click

Install

WLAN Card Utilities/Driver.

4. Click

Next

to creat short cut.

3. Click

Next

to use the default Destination

Folder or click Browse to select another folder.

Summary of Contents for WL-106gM








































Search results

Summary of Contents for WL-106gM

Reviews:

Related manuals for WL-106gM

Brands by name

Popular brands

Asus WL-106gM, User Manual

Search results

Summary of Contents for WL-106gM

Reviews:

Related manuals for WL-106gM

Brands by name

Popular brands