Asus SP97-XV User Manual Download Page 76

Page: 76 / 90

ASUS SP97-XV User’s Manual

IX. SOFTWARE DRIVERS

(Windows 95)

IX. Software Drivers

2.3 Using “Display Modes”

1. Go to “Display Properties” Screen and you will find that “Display Modes” item

had been added.

2. First select “Display Modes” item and you may select desired resolution by

changing “Desktop area” pointer, desired color by changing “Color palette” value,
desired font size by changing “Font size”, and

desired refresh rate by

changing “Refresh rate”.

3. After completing selection, select “OK” or “Apply” to complete the whole in-

stallation.

4. In “SiS 5597/5598 Settings” Screen, select “OK”.

5. Two cases happen :

a). You did not change “color” and/or “font size”.

1. “SiS 5597/5598 Settings” Screen appears again,

2. Select “Yes” and you may work on your selected mode now.

b). You changed “color” and/or “font size”.

1. System will reboot.

2. You may work on your selected mode now.

Summary of Contents for SP97-XV



























































































Search results

Summary of Contents for SP97-XV

Reviews:

Related manuals for SP97-XV

Brands by name

Popular brands

Asus SP97-XV, User Manual

Search results

Summary of Contents for SP97-XV

Reviews:

Related manuals for SP97-XV

Brands by name

Popular brands