Asus P5WD2 Premium, User Manual

Page: 57 / 164

A S U S P 5 W D 2 P r e m i u m A S U S P 5 W D 2 P r e m i u m
A S U S P 5 W D 2 P r e m i u m A S U S P 5 W D 2 P r e m i u m
A S U S P 5 W D 2 P r e m i u m 2 - 3 1 2 - 3 1
2 - 3 1 2 - 3 1
2 - 3 1
• These connectors are set to S t a n d a r d I D E
S t a n d a r d I D E
S t a n d a r d I D E S t a n d a r d I D E S t a n d a r d I D E mode by default. In
S S
S S
S t a n d a r d I D E t a n d a r d I D E
t a n d a r d I D E t a n d a r d I D E
t a n d a r d I D E mode, you can connect Serial ATA boot/data hard
disk drives to these connectors. If you intend to create a Serial ATA
RAID set using these connectors, set the C o n f i g u r e S A T A A s
C o n f i g u r e S A T A A s C o n f i g u r e S A T A A s C o n f i g u r e S A T A A s C o n f i g u r e S A T A A s
item in the BIOS to [RAID]. See section “4.3.6 IDE Configuration” on
page 4-16 for details.
• For RAID 5, use at least three hard disk drives. For RAID 10, use at
least four hard disk drives. Use two to four Serial ATA hard disk
drives for each RAID 0 or RAID 1 set.
I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A I m p o r t a n t n o t e s o n S e r i a l A T A
• You must install Windows ® 2000 Service Pack 4 or the Windows ® XP
Service Pack 1 before using Serial ATA hard disk drives. The Serial
ATA RAID feature (RAID 0/RAID 1/RAID 5/RAID 10) is available only
if you are using Windows
® 2000/XP/Server 2003 or later version.
• When using the connectors in S S S S S tandard IDE t a n d a r d I D E t a n d a r d I D E t a n d a r d I D E t a n d a r d I D E mode, connect the
primary (boot) hard disk drive to the SATA1 or SATA2 connector.
Refer to the table on the next page for the recommended SATA hard
disk drive connections.
4 . 4 .
4 . 4 .
4 . I C H 7 R S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 [ r e d ] , I C H 7 R S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 [ r e d ] ,
I C H 7 R S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 [ r e d ] , I C H 7 R S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 [ r e d ] ,
I C H 7 R S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 [ r e d ] ,
S A T A 2 [ r e d ] , S A T A 3 [ b l a c k ] , S A T A 4 [ b l a c k ] )
S A T A 2 [ r e d ] , S A T A 3 [ b l a c k ] , S A T A 4 [ b l a c k ] )
S A T A 2 [ r e d ] , S A T A 3 [ b l a c k ] , S A T A 4 [ b l a c k ] ) S A T A 2 [ r e d ] , S A T A 3 [ b l a c k ] , S A T A 4 [ b l a c k ] ) S A T A 2 [ r e d ] , S A T A 3 [ b l a c k ] , S A T A 4 [ b l a c k ] )
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
If you installed Serial ATA hard disk drives, you can create a RAID 0,
RAID 1, RAID 5, RAID 10 configuration with the Intel
® Matrix Storage
Technology through the onboard Intel ® ICH7R RAID controller. Refer to
Chapter 5 for details on how to set up Serial ATA RAID configurations.
P5WD2 PREMIUM
®
P5WD2 PREMIUM SATA connectors
SATA1 SATA2
GND RSA
T
A_TXP4
RSA
T
A_TXN4
GND RSA
T
A_RXP4
RSA
T
A_RXN4
GND GND RSA
T
A_TXP3
RSA
T
A_TXN3
GND RSA
T
A_RXP3
RSA
T
A_RXN3
GND
GND RSA
T
A_TXP2
RSA
T
A_TXN2
GND RSA
T
A_RXP2
RSA
T
A_RXN2
GND GND RSA
T
A_TXP1
RSA
T
A_TXN1
GND RSA
T
A_RXP1
RSA
T
A_RXN1
GND
SATA3 SATA4