Asus P2Z-B User Manual Download Page 56 | Manualshive

Page: 56 / 96

background image

ASUS P2Z-B User’s Manual

56

IV. BIOS SETUP

Load Defaults

IV

. BIOS SETUP

Load BIOS Defaults

The “Load BIOS Defaults” option allows you to load the troubleshooting default
values permanently stored in the BIOS ROM. These default settings are non-opti-
mal and disable all high performance features. To load these default settings, high-
light “Load BIOS Defaults” on the main screen and then press <Enter>. The system
displays a confirmation message on the screen. Press <Y> and then <Enter> to
confirm. Press <N> and then <Enter> to abort. This feature does not affect the
fields on the Standard CMOS Setup screen.

Load Setup Defaults

The “Load Setup Defaults” option allows you to load the default values to the sys-
tem configuration fields. These default values are the optimized configuration set-
tings for the system. To load these default values, highlight “Load Setup Defaults”
on the main screen and then press <Enter>. The system displays a confirmation
message on the screen. Press <Y> and then <Enter> to confirm. Press <N> and
then <Enter> to abort. This feature does not affect the fields on the Standard CMOS
Setup screen.

«
...
54
55
56
57
58
...
»

Summary of Contents for P2Z-B

































































































Reviews:

No comments

Related manuals for P2Z-B

Brand: IEI Technology Pages: 234

Brand: Intel Pages: 6

Brand: ECS Pages: 27

Brand: Gigabyte Pages: 8

Brand: AOpen Pages: 105

Brand: Gigabyte Pages: 125

Brand: JETWAY Pages: 56

Brand: Biostar Pages: 37

Brand: JETWAY Pages: 41

Brand: Acrosser Technology Pages: 3

Brand: Gigabyte Pages: 96

Brand: Mach Pages: 86

X99A WORKSTATION

Brand: MSI Pages: 97

Brand: Gigabyte Pages: 108

Brand: Raisonance Pages: 46

Brand: TYAN Pages: 70

Qseven FS700 Series

Brand: DFI Pages: 18

Brand: DFI Pages: 46

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands