Asus CUWE User Manual Download Page 49 | Manualshive

Page: 49 / 136

background image

ASUS CUWE User’s Manual

49

4. BIOS SETUP

4. BIOS SETUP

6. When prompted to confirm the BIOS update, press Y to start the update.

7. The utility starts to program the new BIOS information into the flash

ROM. The boot block will be updated automatically only when neces-
sary. This will minimize the chance that a failed update will prevent
your system from booting up. When the programming is finished, Flashed
Successfully will be displayed.

8. Follow the onscreen instructions to continue.

WARNING!

If you encounter problems while updating the new BIOS, DO NOT

turn off your system since this might prevent your system from booting up. Just
repeat the process, and if the problem still persists, update the original BIOS file
you saved to disk above. If the Flash Memory Writer utility was not able to
successfully update a complete BIOS file, your system may not be able to boot
up. If this happens, your system will need servicing.

Updating BIOS

«
...
47
48
49
50
51
...
»

Summary of Contents for CUWE









































































































































Reviews:

No comments

Related manuals for CUWE

Brand: Intel Pages: 6

Brand: Waveshare Pages: 72

Brand: Infineon Pages: 24

Brand: JETWAY Pages: 70

Brand: Aaeon Pages: 50

Brand: Lucky Star Pages: 77

Brand: Linear Pages: 6

Brand: Supermicro Pages: 124

Brand: Aaeon Pages: 108

Brand: Texas Instruments Pages: 27

Brand: BESTEK Pages: 13

Brand: Linear Technology Pages: 6

dsPICDEM MCHV-3

Brand: Microchip Technology Pages: 68

Brand: MAX power Pages: 20

Brand: Commell Pages: 49

Brand: MSI Pages: 118

Brand: TYAN Pages: 54

PHANTOM GAMING X670E PG Lightning

Brand: ASROCK Pages: 66

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands