C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n
C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n
C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n
C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n
C h a p t e r 4 : M o t h e r b o a r d i n f o r m a t i o n
4 - 1 0
4 - 1 0
4 - 1 0
4 - 1 0
4 - 1 0
3 .
3 .
3 .
3 .
3 .
S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
S e r i a l A T A c o n n e c t o r s ( 7 - p i n S A T A 1 , S A T A 2 )
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
If you installed Serial ATA hard disk drives, you can create a RAID 0 or
RAID 1 configuration with the Adaptec
®
HostRAID™ Technology through
the onboard Intel
®
ICH5R integrated RAID controller.
Serial ATA hard disk drive connection
Serial ATA hard disk drive connection
Serial ATA hard disk drive connection
Serial ATA hard disk drive connection
Serial ATA hard disk drive connection
C o n n e c t o r
C o n n e c t o r
C o n n e c t o r
C o n n e c t o r
C o n n e c t o r
S e t t i n g
S e t t i n g
S e t t i n g
S e t t i n g
S e t t i n g
U s e
U s e
U s e
U s e
U s e
S A T A 1
S A T A 1
S A T A 1
S A T A 1
S A T A 1
M a s t e r
M a s t e r
M a s t e r
M a s t e r
M a s t e r
B o o t d i s k
B o o t d i s k
B o o t d i s k
B o o t d i s k
B o o t d i s k
S A T A 2
S A T A 2
S A T A 2
S A T A 2
S A T A 2
S l a v e
S l a v e
S l a v e
S l a v e
S l a v e
D a t a d i s k
D a t a d i s k
D a t a d i s k
D a t a d i s k
D a t a d i s k
These connectors are set to S t a n d a r d I D E
S t a n d a r d I D E
S t a n d a r d I D E
S t a n d a r d I D E
S t a n d a r d I D E mode by default. In S
S
S
S
S t a n d a r d
t a n d a r d
t a n d a r d
t a n d a r d
t a n d a r d
I D E
I D E
I D E
I D E
I D E mode, you can connect Serial ATA boot/data hard disk drives to these
connectors. If you intend to create a Serial ATA RAID set using these
connectors, set the C o n f i g u r e S A T A A
C o n f i g u r e S A T A A
C o n f i g u r e S A T A A
C o n f i g u r e S A T A A
C o n f i g u r e S A T A As R A I D
s R A I D
s R A I D
s R A I D
s R A I D item in the BIOS to
[Yes]. See section “4.3.5 IDE Configuration” on page 4-16 for details.
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
I m p o r t a n t n o t e s o n S e r i a l A T A
•
You must install Windows
®
2000 Service Pack 4 or the Windows
®
XP
Service Pack 1 before using Serial ATA hard disk drives. The Serial ATA
RAID feature (RAID 0/RAID 1) is available only if you are using Windows
®
2000/XP.
•
Use only two Serial ATA RAID connectors for each RAID 0 or RAID 1
set.
•
When using the connectors in S
S
S
S
S tandard IDE
tandard IDE
tandard IDE
tandard IDE
tandard IDE mode, connect the primary
(boot) hard disk drive to the SATA1 or SATA2 connector. Refer to the
table below for the recommended SATA hard disk drive connections.
®
PVL-D/1U/SCSI
SATA2
SATA1
PVL-D/1U/SCSI SATA connectors
GND
RSA
T
A_TXP1
RSA
T
A_TXN1
GND
RSA
T
A_RXN1
RSA
T
A_RXP1
GND
GND
RSA
T
A_TXP2
RSA
T
A_TXN2
GND
RSA
T
A_RXN2
RSA
T
A_RXP2
GND
