manualshive.com logo in svg

Astronics Trig-Tek 850A, User Manual

Share
Download
Astronics Trig-Tek 850A User Manual Download Page 15

850A/B User Manual                                                                                   Publication No. 980972  Rev. B 

Fault 

When a NC (Normally Closed) contact has a discontinuity longer than the set in 
time interval, it is a FAULT, for NO (Normally Open) contact continuity for a period 
longer than the set in time interval constitutes a fault.  When a FAULT is detected 
the FAULT LED for that channel illuminates and a +12 V signal is present on the 
FAULT output terminal on the rear panel.  To remove the fault the FAULT RESET 
switch should be depressed, this removes the fault from all channels. The FAULT 
RESET can be accomplished remotely by ap12 volts  to the RESET 
terminal on the rear panel. 

 

 

Figure 2-1.  Switch S1 – Input Voltage Setting 

 

Switch S1 

Operation  2-2                                                                                                            Astronics Test Systems 

Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com

Summary of Contents for Trig-Tek 850A



















Reviews:

No comments

Brands by name

Popular brands

Load more brands