background image

Printed in U.S.A. © 2018 Innovative Hearth Products

P/N  900880-00  REV. NC  02/2018

34

Model Number _____________________________________________________
Serial Number _____________________________________________________
Date Installed ______________________________________________________
Dealer’s Name _____________________________________________________
Dealer’s Phone Number ______________________________________________

WARRANTY

Your fireplace is covered by a limited warranty. Please read the warranty 

to be familiar with its coverage.

Retain this manual. File it with your other documents for future reference.

PRODUCT REFERENCE INFORMATION

We recommend that you record the following important information 

about your fireplace.  Please contact your IHP dealer for any questions 

or concerns. 

REPLACEMENT PARTS

See 

Page 28

  for a complete replacement parts list.  Use only parts sup-

plied from the manufacturer.

Normally, all parts should be ordered through your IHP distributor or 

dealer. Parts will be shipped at prevailing prices at time of order.

When ordering repair parts, always give the following information:

1.

 The model number of the appliance.

2.

 The serial number of the appliance.

3.

 The part number.

4.

 The description of the part.

5.

 The quantity required.

6.

 The installation date of the appliance.

If you encounter any problems or have any questions concerning the 

installation or application of this system, please contact your dealer.

IHP

1508 Elm Hill Pike, Suite 108 

Nashville, TN 37210

Visit us at Astria.us.com

IHP reserves the right to make changes at any time, without notice, in design, materials, 

specifications, prices and also to discontinue colors, styles and products.  Consult your local 

distributor for fireplace code information.

1508 Elm Hill Pike, Suite 108 • Nashville, TN 37210

P900880-00

Summary of Contents for 900880-00



































Reviews: