NOTE: DIAGRAMS & ILLUSTRATIONS ARE NOT TO SCALE.
INNOVATIVE HEARTH PRODUCTS • LINEAR GAS FIREPLACES • REQUIRED AND OPTIONAL ACCESSORIES
4
*For PF2 System, see
Page 5
and
Figure 12.
Control Compartment
Access Panel and
Gasket
Right Burner Bracket
Orifi ce
Slot
Figure 7 - Accessing the control compartment
3
. Loosen the front left screw of the right burner bracket. Remove
the other three screws, and rotate the bracket clockwise to
uncover the slot in the fi rebox fl oor
(
Figure 7
)
.
Connect wiring harnesses for blower and optional
fi rebox panel backlight kit - PF1 System*
NOTE:
Use only original, factory-supplied wiring inside fi replace.
1.
In the control compartment, use a screwdriver or other
blunt object to carefully break the sealant around the wires.
NOTE:
Be careful not to damage the wires.
2.
Plug the multiwire harness (provided with the fi rebox panel
backlight kit) into the SimFlame™ (fl icker) module port with
the red wires
(
Figure 8
)
.
NOTE:
If not installing the SimFlame module, plug the
multiwire harness directly into the power harness (omit the
components outlined in
Figure 8
)
and skip
step 3
.
Multiwire Harness from
Panel Backlighting Kit
SimFlame
Module
(Plug into
AUX OUT
on Control
Module)
Power
Harness
If not using SimFlame
(flicker) module, omit
outlined components.
Figure 8 - Connecting multiwire harness and fl icker module
3
. Plug the power harness (provided with the fi rebox panel
backlight kit) into the SimFlame Module port with the black
and white wires
(
Figure 9
)
.
FAN
AUX
OUT
SimFlame
Slot
SimFlame
Module
Fan Control
Module
Plug blower
into FAN port
Plug lights into
AUX OUT port
Figure 9 - Connecting the lights and blower
4
. Route the lighting wiring up through the access opening, and
slide it into the slot
(
Figure 9
)
.
5
. Plug the power plug end of the power harness into the AUX
OUT port on the fi replace fan control module
(
Figure 9
)
.
Install refl ector (from optional fi rebox panel backlight kit)
1.
Insert the bottom edge of the refl ector (provided with the
fi rebox backlight kit) into the fi replace fi rst. Then, push the
top edge into rear of fi replace
(
Figure 10
)
.
NOTE:
Lift the refl ector over the tabs on the rear ledge of the
fi replace
2.
Align the large hole in the lower face of the refl ector over the
screw in the fi rebox rear wall.
3.
Align the screw holes in the top and bottom edges of refl ector
with the rear most holes in the fi replace ceiling and rear ledge.
Secure the refl ector using six (6) #10-16 x 3/8 hex-head sheet
metal screws provided with the fi rebox panel backlight kit.
~
Refl ector
Fireplace
Front
Tab
Rear Ledge
Figure 10 - Installing the refl ector
Install side panels (from required fi rebox panel kit)
1.
Align the screw hole in the top fl ange of the side panel with
the upper hole in the inside wall of the fi replace
(
Figure 11
)
.
2.
Align the screw holes in the bottom fl anges of the side
panel with the holes in the front and rear ledges.
3.
Secure each panel with three (3) #10-16 x 3/8 hex-head
sheet metal screws provided with the fi rebox panel kit.
Left Side
Panel
Right
Side
Panel
~
Left Side
Panel
Front
Ledge
Rear
Ledge
~
Figure 11 - Installing the side panels
f i r e - p a r t s . c o m