Aston Global AWB-139CML Installation Operation User Manual Download Page 27

Page: 27 / 30

www.astontechusa.com

Aston Magnetic Levitation Wheel Balancer AWB-139ML User’s Manual

⚫

Proceed a spin again, when the wheel stops

spinning, the display shows as the picture

illustrated.

⚫

Press key to save the calibration data and complete the calibration.

2.2

Distance

Calibration

(Available with Auto data entry models only)

⚫

Press keys to enter the

distance calibration.

⚫

Pull out the front measuring arm to the

ruler scale 10 cm position.

⚫

Press ALU key to confirm and see the display

as illustration show

⚫

Move the arm to point at the spin unit flange as shown in the figure, hold it and press the ALU

to complete the calibration.

2.3 Diameter

Calibration

⚫

Press keys to enter the

diameter calibration.

Summary of Contents for AWB-139CML































Search results

Summary of Contents for AWB-139CML

Reviews:

Related manuals for AWB-139CML

Brands by name

Popular brands

Aston Global AWB-139CML, Installation Operation User Manual

Search results

Summary of Contents for AWB-139CML

Reviews:

Related manuals for AWB-139CML

Brands by name

Popular brands