manualshive.com logo in svg

Aston Global AWB-139CML, Installation Operation User Manual

Share
Download
Aston Global AWB-139CML Installation Operation User Manual Download Page 26

 

www.astontechusa.com 

 

25 

                 

Aston Magnetic Levitation Wheel Balancer AWB-139ML User’s Manual 

 

 

 

 

CALIBRATIONS 

2.1. Balancing Calibration 

⚫

 

Use a wheel with steel rim of average dimension (for example, 6''x 15'') mount it properly on 

the spin shaft. Enter wheel data 

A

，

W 

and

 D 

correctly.

 

 

⚫

 

Press  Fn      and      C  +      keys  to  enter  calibration. 

The  position  indication  bar  blinks  and  the  display 

shows as picture illustrated.   

 

⚫

 

Spin the wheel, when the wheel 

stops spinning, the display shows as 

picture illustrated.

 

 

 

 

 

⚫

 

Mount 

the 

provided 

calibration 

weight 

(100g) 

on 

the

                                           

                   

OUTER (right) side of the rim at any position. 

 

 

⚫

 

Proceed  a  spin  again,  when  the  wheel  stops 

spinning,  the  display  shows  as  the  picture 

illustrated. 

⚫

 

Remove the calibration weight (100g) from the right side of the rim and put it on the left 

side of the rim at the same angular position. 

 

Summary of Contents for AWB-139CML































Reviews:

No comments

Brands by name

Popular brands

Load more brands