background image

 

       Aston® 

Overhead Two Post Lift AL-100RH User’s Manual  

18.

 

Position  the  lift  support  pads  to  contact  the  vehicle  manufacturers  recommended  lifting  points.  Raise  the  lift  until  the 
pads  contact  the  vehicle.  Check  pads  for  secure  contact  with  the  vehicle.  Check  all  arm  restraints  and  insure  they  are 
properly engaged. Raise the lift to the desired working height.  
 

19.

 

Some pickup trucks may require an optional truck adapter to clear running boards or other accessories.  
 

20.

 

NOTE: Always use all 4 arms to raise and support vehicle.  
 

21.

 

Caution! Never work under the lift unless the mechanical safety locks are engaged.  
 

22.

 

Note that the removal or installation of some vehicle parts may cause a critical load shift in the center of gravity and may 
cause the vehicle to become unstable. Refer to the vehicle manufacturer’s service manual for recommended procedures.  
 

23.

 

Always keep the lift area free of obstruction and debris. Grease and oil spills should always be cleaned up immediately.  

 

24.

 

Never raise vehicle with passengers inside.  

 

25.

 

Before lowering check area for any obstructions.  

 

26.

 

Before removing the vehicle from the lift area, position the arms to the drive-thru position to prevent damage to the lift 
and /or vehicle.  

 

27.

 

Do not remove hydraulic fittings while under pressure.  

  

WARNING! 

Failure by purchaser to provide the recommended mounting surface could result in unsatisfactory lift performance, 

property damage, or personal injury.  

  
LOCATION

 This lift has been evaluated for indoor use only with an operating ambient temp. range of 41- 104°F (5 - 40°C). It is 

prohibited  to  install  this  product  outdoors. 

Failure  to  adhere  will  result  in  decertification,  loss  of  warranty,  and  possible 

damage to the equipment. 

For  additional  safety  instructions  regarding  lifting,  lift  types,  warning  labels,  preparing  to  lift,  vehicle  spotting,  vehicle  lifting, 
maintaining  load  stability,  emergency  procedures,  vehicle  lowering,  lift  limitations,  lift  maintenance,  good  shop  practices, 
installation, operator training and owner/employer responsibilities

please refer to “Lifting It Right” (ALI/SM) and “Safety Tips” 

(ALI/ST) and vehicle lift points for service garage lifting SAE J2184.    
 
For additional  instruction on  general  requirements for lift  operation, please  refer to “Automotive  Lift-Safety Requirements  for 
Operation,  Inspection  and  Maintenance”  (ANSI/ALI  ALOIM).  Installation  shall  be  performed  in  accordance  with  ANSO/ALI 
ALIS, Safety Requirements for Installation and Service of Automotive Lifts.  

  

 

 

 

 

 

 

 

 

Summary of Contents for AL-100RH























Reviews: