Astera ART3 User Manual Download Page 11

Operation Modes 

Chapter 

 4 

4.4 RC Receiver

To   start   this   mode,   choose   RC   RECEIVER   in   the   top   navigation   and   confirm   with 
Enter.

By using the RC Receiver mode, third-party RGB lamps can be integrated in a light setup 
that is not controlled by Wireless DMX but by the ARC2 remote control.

Up to 32 externally connected RGB fixtures can be controlled individually. The ART3 has to 
be setup to the number of connected pixels, to replay programs correctly. This is done using 
the 

AUTO PIXELS

 parameter.

Apart from Auto Pixels a range of values can be set to control the connected third-party 
lamps directly from the ART3 without the need for an ARC2 remote control.

Auto Pixels

Sets the number of pixels that replay programs. Setting the value to 
ten means that a program will stretch over ten lamps.

Local Group

Assigns the lamps to one of the four groups for easy addressing. 

Local Set Number

Assigns the lamps to one of 256 possible sets for easy addressing.

Program

Plays one of 20 pre-defined programs that can be customized with  
colors, intensity, power scheme, speed, fade, directions, etc.

Intensity

Sets the brightness of the lamps.

Power Scheme

Three different power schemes can be set to optimize the lamp for  
high-brightness, maximum runtime or normal playback.

Speed 

Sets the speed with which a program is played.

Fade 

Sets the fading transitions between between different colors from hard 
transitions to smooth transitions. 

Direction 

Sets the direction of a program and wether it loops continuously or is 
played only once.

Strobo Speed

Starts the strobe-light and defines the frequency of the stobe effect

Random Mode

Switches a random mode on which displays programs at a changing 
rate.

Random Fade

Defines the radom fade.

Random Speed

Defines the random speed.

Groups

GROUPS defines over how many of the 4 Groups a displayed program 
stretches. Usually this is set automatically by the ART3.

Offset

Offset defines where the LOCAL GROUP starts. Usually this is set  
automatically by the ART3.

Chain Size

Creates a chain of lamps that enable programs to stretch over several 
lamps.

Position in Chain

Assigns a position inside the chain to all lamps connected to the ART3

Set Size

Defines over how many lamps a set stretches. 

Position in Set

Defines which position in a set a lamp has.

Color 1

Sets color 1 that is used to display programs

Color 2

Sets color 2 that is used to display programs

11

Summary of Contents for ART3






















Reviews: