background image

IS-M19  Rev 4  05/22

M19, FM19, M190 and FM190 
Intermediate Pivot

3/4" Offset, Handed
Installation Instructions

Copyright © 2006, 2009, 2022, ASSA ABLOY Accessories and Door Controls Group, Inc. All rights reserved. Reproduction in whole or 

in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group, Inc. is prohibited.

NORTON

RIXSON

Ce produit peut vous exposer au plomb qui, dans l’état de la 

Californie, est reconnu pour causer le cancer, des anomalies 

congénitales ou d’autres problèmes de reproduction. Pour 

plus d’informations, visitez: www.P65warnings.ca.gov.

This product can expose you to lead which is known to 

the state of California to cause cancer and birth defects or 

other reproductive harm. For more information go to  

www.P65warnings.ca.gov.

WARNING

1.  Install intermediate pivot.

1.  Determine hand of door for proper placement of 

intermediate pivot. (Figure 1)

NOTE: 
–  

Door should already be hung with top pivot and 

bottom pivot or floor closer.

–  

Doors 60" - 90" (152.4cm - 228.6cm) in height 

should use one Intermediate pivot; each 

additional 30" (76.2cm) warrants an additional 

Intermediate pivot.

2.  Locate pivot(s) so that it is vertically in alignment 

with centerpoint of top pivot and bottom spindle 

and mark pivot leaf locations on door and frame. 

(Figure 2) 

3.  Mortise door and frame. (Figure 3) Refer to 

template IP50050.

4.  Using pivot leaf as a template mark and prepare 

mounting holes on door and frame. (Figure 3)

5.  Install jamb portion of pivot in frame using five 

(5) 1/4-20 x 5/8" FHMS or #14 x 1-1/2" FHWS screws 

provided. 

6.  Install door portion of pivot in door using five (5) 

1/4-20 x 5/8” FHMS or #14 x 1-1/2” FHWS screws 

provided.

IMPORTANT: It is responsibility of door 

and frame manufacturers to check 

hardware schedule and prepare doors 

and frames. The following instructions 

cover field prep.

To Determine Your Hand of Door:

Figure 1 

Door Stop

1/8" (3.2) Minimum From

Face of Door to Door Stop

F

Right Hand Door

Door

Jamb

13/16" (20.6) From Face

of Jamb to C of Pivot Pin

L

5/16

/

(7.9)

5/16

(7.9)

1/4

(6.8)

3/4" (19) From Face of

Door to C of Pivot Pin  

L

E

3/4" (19) From Door

Edge to C of Pivot Pin

L

Figure 3 

Figure 2 

Approved 2022-05-23

Summary of Contents for NORTON RIXSON M19

Page 1: ...loser Doors 60 90 152 4cm 228 6cm in height should use one Intermediate pivot each additional 30 76 2cm warrants an additional Intermediate pivot 2 Locate pivot s so that it is vertically in alignment with centerpoint of top pivot and bottom spindle and mark pivot leaf locations on door and frame Figure 2 3 Mortise door and frame Figure 3 Refer to template IP50050 4 Using pivot leaf as a template ...

Page 2: ...r to desired height Figure 5 4 Using shims furnished with bottom arm fill gap between arm and bottom pivot floor portion Figure 6 5 Turn stud screw counter clockwise until door rests on shims Figure 5 6 Tighten locking screw of bottom pivot Figure 6 NOTE Open and close door several times Make shim adjustments until door swings freely 7 Re tighten locking screw and replace arm cap Figure 6 8 Replac...

Page 3: ...hout the express written permission of ASSA ABLOY Accessories and Door Controls Group Inc is prohibited NORTON RIXSON NORTON RIXSON 3 8 9 5 1 7 16 36 5 2 1 2 63 5 3 9 16 90 5 4 5 8 117 5 1 15 16 49 2 1 1 8 28 6 13 16 20 6 5 16 7 9 5 127 5 127 7 16 11 1 1 1 8 28 6 2 1 2 63 5 3 7 8 98 4 4 9 16 115 9 3 15 32 88 1 1 17 32 38 9 1 1 8 28 6 5 16 7 9 13 16 20 6 2 1 8 54 DOOR LEAF JAMB LEAF A A 1 8 3 2 13 ...

Page 4: ...A ABLOY Accessories and Door Controls Group Inc All rights reserved Reproduction in whole or in part without the express written permission of ASSA ABLOY Accessories and Door Controls Group Inc is prohibited Technical Product Support Monroe NC 28112 USA Phone 877 974 2255 ext 2 Techsupport NortonRixson assaabloy com NortonRixson com NORTON RIXSON Approved 2022 05 23 ...

Reviews: