CHANGING USER CARDS
1.
Place the Service card in front of the antenna without adding user card. You will hear two-tone beep alarm and blue LED flash on.
After 2 seconds high beep alarm with blue LED flashing on will be followed by unblocking the knob for 4 second or until the user
rotate the knob. Turn the knob in “open” position.
OPENING
1. Place the card that was locking, before the antenna. This is followed by short beep alarm and blue LED indication. The knob shall
release.
2. Within 6 seconds turn the knob in opening direction.
LOCKING
1.
Place the card in front of the antenna within 2 seconds. After hearing the short beep alarm and short blue flashing, the knob shall
release for locking.
2.
Within 6 seconds turn the knob in locking direction. The lock shall block immediately after locking followed by short beep and blue LED
flashing on.
ATTENTION:
IF THE CARD USED FOR OPENING IS NOT THE SAME USED FOR LOCKING, THE LOCK SHALL GIVE WARNING WITH
RED
LED
INDICATION.
SO
THE
CARD
IS
NOT
AUTHORIZED
TO
OPEN
THE
LOCK.
THE DEVICE WILL BLOCK AFTER 5 UNAUTHORIZED ATTEMPTS. THE DEVICE WILL INDICATE THIS WITH 5 QUICK RED LED
FLASHES EVERY 20S OR EVERY TIME YOU SHOW A CARD TO THE ELECTRONIC LOCK. THE DEVICE WILL BE BLOCKED FOR
60S
.
THIS IS VALID FOR THE PERMAMENT AND CHANGING USERS!
SERVICE CARD
There is recorded a Service card in the lock memory. It has the following functions on the lock control:
OPENING WITH SERVICE CARD.
Opening without deleting the customer card.
1.
Place the Service card before the antenna. Firstly you will hear high and low beep alarm with blue LED flashing on. After 2 seconds the
blue LED shall turn on again followed by high beep alarm. The device will unblock the knob for 4 seconds.
2.
Rotate the knob in position “open” and you will hear high and low beep alarm with blue LED flashing on.
3.
If the lock is closed with the service card the user card will not be lost.
EREASE CARD
There is recorded an Erase card in the lock memory by the manufacture. It has the fallowing function on the lock control:
FACTORY RESET
ATTENTION: THIS WILL ERASE ALL CARD INCLUDING THE SERVICE CARD!
1.
By placing the Erase card before the antenna within 2 second. After hearing the long beep and blue LED long flashing on, knob
shall be released. Turn the knob in position “close”.
2.
Within 2 second after locking, the lock will indicate with red LED flashing on every 4 second the need of recording new Service
card.
POWER SUPPLY AND BATTERY CHANGE
The lock operates with three batteries 1.5V, ААА type. In order to change them, reel off screw М4 and loose the М18х1 nut. Roll the lock
around its axis and change the batteries keeping their polarity. Assembly the lock the same way.
**PLEASE,
USE
ALKALINE
BATTERY
ONLY!
ATTENTION:
If the battery voltage is too low (the battery is empty), each lock manipulation shall finish with indication about necessary change:
30% - Long red flash(CONSIDER BATTERY CHANGE!);
20% - Long red flash fallowed by one quick red flash;
10% - Long red flash fallowed by two quick red flash;
0% - Long red flash fallowed by three quick red flash(the device may not work properly at this percentage);
In case the batteries are completely empty, slide the cover located at the lower side of the lock to ensure entrance for the lock USB micro
coupling. Place the micro USB coupling in the lock. The cable must be connected to the emergency power supply, or to a laptop, tablet, or another
devices ensuring 5V via USB*.
Place the client card in front of the antenna and open the lock. Change the batteries following the described above manner. Slide the cover
back in order to block the entrance to the lock coupling.
*When the lock is in “Changing user” mode and the position of the knob is “Close” use the Service card to open the lock.
