Assa Abloy Cabinet Lock Series Installation Instructions Manual Download Page 10

Page: 10 / 12

Part Number 3085006.001, Rev 3

15.

INSTALL for the double-door strike plate mounting bracket. (OPTIONAL)

NOTE: The double-door strike plate bracket requires that one door can be inactive or secured.

PLACE the bracket on door, making sure it aligns with the mark made in Step 2c and the edge of the door.

MARK the door.

REMOVE the bracket and DRILL pilot holes at the two marks.

INSTALL the bracket using the provided mounting screws.

16.

INSTALL the double-door strike plate.

PLACE the strike plate over the holes on the bracket.

INSERT and TIGHTEN the three 6-32 x 5/16” (3.5 mm x 7.94 mm) provided screws.

FCC Statement

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation.

IC Statement

This device complies with Industry Canada license-exempt RSS standards(s). Operation is subject to the following
two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation.

15a and 15b 15c and 15d

Summary of Contents for Cabinet Lock Series












