background image

2

  General Description 

 

 

2) General Descriptions

The Access 800

®

 TCNE1 Rim, SecureBolt™ and Mortise Exit Device offers the ability to seamlessly 

integrate Grade 1 security into an existing Wiegand compatible access control system. Monitoring capabilities 

for Rim and SecureBolt include Request to Exit and Door Position Switch. 

Note:

 Mortise Exit devices offer 

Request to Exit and Door Position Switch and can monitor the latchbolt and/or Deadbolt of the Mortise Lock 

when connected to the Auxiliary Relay Module incorporated into the Network Interface Cabinet.

Features

• Complete monitoring of doors from lock

s

• Network Interface board connects to most third party access control point

s

• Panel interface board accommodates up to 4 lock

s

• HID 125khz proximity credential

s

• Supports Fail-Safe and Fail-Secure 24VDC Solenoid Locking Device

s

3) Features / Specifications

Access

Control

Panel

NETWORK INTERFACE

CABINET

*

*

*

*

 Items Supplied with Exit Device 

Items included with ED5200N (S) (A) Rim or

   Items included with ED5600N (A) Series     

 SecureBolt Exit Device by 9800 TCNE1

         Mortise Exit Device by 9M800 TCNE1

• Outside Escutcheon with Ke

ypa

d

         • Outside Escutcheon with Keypad 

• Outside Solenoid Trim Assembl

y

   • Outside Solenoid Trim Assembl

y

• Exit Device

    • Exit Device 

• Inside Escutcheon with Circuit Board

   • Inside Escutcheon with Circuit Board

• Screw Pack 

    • Screw Pack

  Specifications 

• Latch 

– 3

/4" throw, stainless steel

• Latch  3/4" throw, 

a

nti-friction, stainless steel

• Outside Solenoid driven lever controlled b

y

 keypad         • Outside Solenoid driven lever controlled b

y

 keypad  

• Push bar retracts latch from inside

• Push b

a

r retracts latch from inside  

• 

F

ire sto

p

 

p

rovided for 

f

ire r

a

ted doors

         • Fire stop 

p

rovided for 

f

ire r

a

ted doors 

 • Exit devices furnished for 1 3/4" 

– 2

 1/4" doors

• Exit devices furnished for 1

-3/4"

 

- 2

 1/4

"

 doors

• UL Listed

• UL Listed

  • Accepts all Corbin Russwin Inc. mortise cylinders 

• Accepts all Corbin Russwin Inc. rim cylinders 

(9M805 only

)

  (9803 only

)

    • Key retracts latch 

(9

M805 only) 

• Ke

y

 allows lever to retract latch (9803 only

)

  • Av

a

il

a

ble in 

a

ll lever handle designs  

• Av

a

il

a

ble in 

a

ll lever handle designs 

Series Trim

Series Trim

• Weatherseal gaskets and conduit 

• Weatherseal gaskets and conduit 

  Specifications 

Summary of Contents for 9800 TCNE1 Series






















Reviews: