Check screw length is correct.
For 1220 & 1420, ensure
screws do not protrude
through outer furniture.
For Round Rose Furniture
Insert fixing screws through
inner retainer rose.
Mount furniture on door
through lock or latch.
Secure furniture by
tightening fixing screws.
For Square Rose Trim Furniture
(1420 only)
If required, fix grub
screw to outer
square rose with allen
key supplied.
For Captive Rose Furniture
(1220 & 1420 only)
For Captive Rose Furniture
levers, loosen and undo
outer rose trim.
Rotate lever 45° and
position rose trim to allow
clear access to fixing screw
holes.
Insert fixing screws.
ASSA ABLOY Australia Pty Limited, 235 Huntingdale Rd, Oakleigh, VIC 3166 ABN 90 086 451 907 2021
Experience a safer and more open world
Use the appropriate tailbar according to the turn combination mounted.
For single side turn only
P/No. TAILBAR-S1
Suits - 30-40mm doors
P/No. TAILBAR-S2
Suits - 40-50mm doors
1. Insert spring and tailbar into end of
turn knob as above. Push tailbar until
engaged and retained in turn knob.
Refer above for correct tailbar for your
door thickness.
2. Engage tailbar end into turn snib adaptor
as shown.
For privacy configuration (Turn on both sides)
P/No. TAILBAR-E1
Suits 32-45mm doors
1. Insert spring and narrow end
of tailbar into turnknob or
disabled accessible turn until
engaged and retained.
2. Pass tailbar completely through the turn
snib adaptor as shown.
3. Make sure tailbar engages with the turn
escutcheon on the other side of the lock.
3 Door Preparation
4 Mounting Plate Furniture with Turn Configurations
5 Final Assembly
Turn examples:
If required, cut screws to length as indicated. Deburr end of cut screws.
Note: Do not cut with pliers or side-cutters as this is likely to cause thread damage upon
assembly.
Mark hole centres accurately and drill holes required.
Remove lock from mortice and place the template in the correct alignment according to
the backset required.
Cut out template from instruction sheet.
Turn knob
Emergency
Turn
Disabled
Accessible turn
THIS IS A COMMON TEMPLA
TE FOR INST
ALLA
TION OF
LOCKW
OOD COMMERCIAL DOOR FURNITURE WHEN
USED WIT
H T
HE L
OCKW
OOD SERIES MORT
ICE L
OCKS.
NOTE: BEFORE DRILLING HOLES CHECK SUIT
ABILITY
WIT
H L
OCKSET AND FURNITURE T
O BE FITTED. FOR
ALL OT
HER DET
AILS REFER T
O L
OCK MOUNT
ING
INSTRUCT
IONS.
ENSURE L
OCK IS REMO
VED FROM MORT
ICE BEFORE
DRILLING HOLES. DO NOT DRILL HOLES RIGHT
THROUGH DOOR T
O PREVENT POSSIBLE D
AMA
GE
TO DOOR F
ACE.
BORE 2 HOLES 20mm DIA FOR O
VAL
CYLINDER ONL
Y
BORE HOLE 22mm DIA FOR TURN KNOB ONL
Y
DRILL HOLE 22mm DIA
DRILL HOLE 6.5mm DIA PLA
TE
FURNITURE
DRILL HOLE 6.5mm DIA
FOR T
HROUGH
FIX INST
ALLA
TION
DRILL HOLE 10mm DIA DIA
GONAL
FIX FURNITURE
DRILL HOLE 6.5mm DIA
HORIZONT
AL
FIX FURNITURE
TEAR HERE
TEAR HERE
ALIGN TEMPLA
TE EDGE WIT
H BOTT
OM
OF CO
VERPLA
TE RECESS ON DOOR EDGE
FOLD ALONG DOTTED LINE AND ALIGN TEMPLA
TE WITH EDGE OF DOOR
127mm B
ACKSET
89mm B
ACKSET
60mm B
ACKSET
CUT OUT
HOLE
CUT OUT
HOLE
LA
TCH HOLE POSIT
ION
MORTICE
CENTRELINE
FOLD ALONG DOTTED LINE AND ALIGN TEMPLATE WITH EDGE OF DOOR
ALIGN TEMPLA
TE EDGE WIT
H BOTT
OM
OF CO
VERPLA
TE RECESS ON DOOR EDGE
127mm B
ACKSET
89mm B
ACKSET
60mm B
ACKSET
BORE 2 HOLES
20mm DIA FOR O
VAL
CYLINDER ONL
Y
BORE HOLE 22mm DIA FOR TURN KNOB ONL
Y
DRILL HOLE 22mm DIA
DRILL HOLE 6.5mm DIA
PLA
TE
FURNITURE
DRILL HOLE 6.5mm DIA FOR T
HROUGH
FIX INST
ALLA
TION
DRILL HOLE 10mm DIA DIA
GONAL
FIX FURNITURE
DRILL HOLE 6.5mm DIA HORIZONT
AL
FIX FURNITURE
