background image

*740158*

740158

General

The Benchmark is an automatic electromechanical swinging door operator for use on hinged, center pivoted and offset pivoted doors. 

When activated, the Benchmark drives the door to full open position, then electrical power is turned off and the door is closed by spring 

force. The activating circuit opens the door from any position in the closing swing. During a power failure, the Benchmark acts as a 

manual door closer (Size 3). Door opening and closing cycles, including opening speed, back check speed, hold open time delay, closing 

speed, and latch position, are adjustable.

Warning

always disconnect main power to the operator prior to 

servicing or cleaning.

  

Caution

this operator is for indoor use only.

Do not mount any accessories directly to the operator.

Replacement Parts & System Components

Part

27” Header

Full Length Header 

Single

Full Length Header Double

Premium Control 

Box

9130-3462SC 

9140-3462SC

9130-3462SC 

9140-3462SC

9150-3462SC

Gear Box

9130-3454S 

9140-3554S

9130-3454 

9140-3454

9150-3454S

End Caps

9130-334

9140-334

9150-334

Part

Pull

Standard Push

Extended 

reveal Push

Finish

Arm Assembly

9130-3077T

9140-3077 

9150-3077

9140-3077L 

9150-3077L

US28 

DC13

Table of Contents

General .....................................................................................................................................................................................................1
Replacement Parts & System Components .............................................................................................................................................1
Replacement Parts & System Components (Cont.) .................................................................................................................................2
1 Pre-Installation Site & Product Check....................................................................................................................................................3
2 Operator Installation ..............................................................................................................................................................................4
3 Wiring.....................................................................................................................................................................................................7
4 Arm & Cover Installation ........................................................................................................................................................................7
5 Operational Check .................................................................................................................................................................................9
6 Operator Adjustment ............................................................................................................................................................................10
7 Release for Service ............................................................................................................................................................................. 11
8 Benchmark III Software ....................................................................................................................................................................... 11

Swing Operator

Models 9130, 9140 & 9150

Benchmark III

Installation Instructions

Summary of Contents for Benchmark III 9130














Reviews: