manualshive.com logo in svg

Aspire Community & Homecare Bed Range, User Manual

Share
Download
Aspire Community & Homecare Bed Range User Manual Download Page 23

23

12. SPECIFICATIONS

Degrees of Movement

A.  Upper body profiling 

60° Max.

B.  Lower body profiling 

30° Max.

C.  Trendelenburg 

10.5° Max.

D.  Reverse Trendelenburg    10.5° Max.

Weight Capacity

Leg 510mm

Main Actuator 706mm

2020 - 2120mm

990mm

Thigh 349mm Sacral 217mm Upper Body 718mm

Highest

1100mm

Lowest

710mm

156mm

B

A

C

D

Leg 510mm

Main Actuator 706mm

2020 - 2120mm

990mm

Thigh 349mm Sacral 217mm Upper Body 718mm

Highest

1100mm

Lowest

710mm

156mm

B

A

C

D

BACKREST 

INCLINE/DECLINE

60°

KNEE BEND 

INCLINE/DECLINE

30°

TRENDELENBURG 

TILT

12° (both ends)

S.W.L

150 kg

BED HEIGHT RANGE

220 – 710 mm

BED WIDTH

940 mm

MATRESS PLATFORM 

LENGTH

2020 – 2120 mm 

(in 25mm increments)

Safe Working Load: 220kg
(inc. mattress & accessories)
Max. Patient Load: 180kg

Component Weights:

Mattress Platform – Head End    17.6kg 
Mattress Platform – Foot End 

17.6kg 

Head/Foot Ends (each)                17kg
TiMotion System (inc handset) 

5kg

Self Help Pole 

6.2kg

Summary of Contents for Community & Homecare Bed Range




























Reviews:

No comments

Brands by name

Popular brands

Load more brands