background image

 

Batty Safety 

 

The area in which the units are charged should be clear of debris and 

combustible materials or chemicals.    Particular care should be taken where the 

device is charged in a non -commercial environment.   

 

Follow battery usage, storage, and charging guidelines found in the user guide.   

 

Improper battery use may result in a fire, explosion, or other hazard.   

 

To charge the device battery, the battery and charger temperature must be 

between 0

~+50

 

 

Do not use incompatible batteries and chargers.    Use of an incompatible battery 

or charger may present a risk of fire, explosion, leakage, or the hazard.   

 

Do not disassemble or open, crush, bend or deform, puncture, or shred.   

 

Severe impact from dropping any battery-operated device on a hard surface 

could cause the battery to overheat.   

 

Do not short circuit a battery or allow metallic or conductive objects to contact 

the battery terminals.   

 

Do not modify or remanufacture, attempt to insert foreign objects into the 

battery, immerse or expose to water or other liquids, or expose to fire, explosion, 

or other hazard.   

 

Do not leave or store the equipment in or near areas that might get very hot, 

such as in a parked vehicle or near a radiator or other heat source. Do not place 

battery into a microwave oven or dryer.   

 

Battery usage by children should be supervised.   

 

Please follow local regulations to promptly dispose of used re-chargeable 

batteries.   

 

Do not dispose of batteries in fire.   

 

Seek medical advice immediately if a battery has been swallowed. In the event of 

a battery leak, do not allow the liquid to come in contact with the skin or eyes. If 

contact has been made, wash the affected area with large amounts of water and 

seek medical advice. 

 

Marking and European Economic Area (EEA) 

 

Frequency of Operation 

 

The use of 2.4 GHz RLAN's, for use through the EEA, have the following restrictions:   

 

Maximum radiated transmit power of 100 mW EIRP in the frequency range 2.400 

- 2.4835 GHz   

 

France, outside usage is restricted to 2.4 - 2.454 GHz.   

Summary of Contents for TN450A1





















Reviews: