background image

particles ( such as grain, dust, or metal powders ) and any other area where you 

would normally be advised to turn off your vehicle engine.   

 

Safety in Aircraft 

Turn off your wireless device whenever you are instructed to do so by airport or 

airline staff.     

 

Safety in Hospitals   

Wireless devices transmit radio frequency energy and may affect medical electrical 

equipment.      Wireless devices should be switched off whenever you are requested 

to do so in hospitals, clinics or healthcare facilities.        These requests are designed 

to prevent possible interference with sensitive medical equipment. 

 

Safety Information – Europe   

This device was tested for typical body-worn operation.    Use only TURBONET tested 

and approved accessories to ensure EU compliance. 

 

Laser Devices   

Class 2 laser scanners use a lower power, visible light diode.    As with any very bright 

light source, such as the sun , the user should avoid staring directly into the light 

beam.    Momentary exposure to a class 2 laser is not known to be harmful.   

Caution: Use of controls, adjustments or performance of procedures other than 

those specified herein may result in hazardous laser light exposure.   

 

Power Adaptor   

 

Use only a TN450A1 approved Power Adaptor with electrical ratings : Output 

5VDC, min 2A, with a maximum ambient temperature of at least 45

℃.

 

 

Use of alternative power adaptor will invalidate any approvals given to this device 

and maybe dangerous.   

 

Battery Information 

Use only a TURBONET approved batteries.   

When batteries are stores over six (6) months, some irreversible deterioration in 

overall battery quality may occur.    Store batteries at half of full charge in a dry, cool 

place, removed from the equipment to prevent loss of capacity , rusting of metallic 

parts and electrolyte leakage.      When storing batteries for one year or longer, the 

charge level should be verified at least once a year and charged to half of full charge. 

 

Summary of Contents for TN450A1





















Reviews: