Askey RT210W User Manual Download Page 10

Page: 10 / 59

Wireless Broadband Router User Manual

•

802.11g Wireless LAN

•

Build-in two internal antenna for wireless technology

•

PPPoE (PPP over Ethernet) Client with Keep
Alive/Connect On Demand Support

•

PAP and CHAP Authentication

•

DHCP Client

•

MAC Address Cloning

•

DHCP Server

•

NAT

•

Firewall Support

•

Bridge Mode Support

•

802.1D Spanning Tree Bridging

•

IP Filtering, IP Forwarding

•

DMZ Hosting

•

ASCII/HEX Format 64/128 Bit WEP Key for Wireless LAN

•

Allow List for Wireless LAN

•

VPN Support (IPSec Passthrough, and PPTP
Passthrough)

•

Configurable through Web Browser via WAN/LAN

•

Software Upgrade

•

NTP/Manual System Clock

•

Configuration Saving/Retrieving

•

Event Log

1.3 Package Contents

Check the contents of the package against the pack contents
checklist below. If any of the items is missing, then contact the
dealer from whom the equipment was purchased.

•

Wireless Broadband Router

•

Power Adapter and Cord

•

CD-ROM x1

•

RJ-45 Ethernet Cable

Summary of Contents for RT210W




























































Search results

Summary of Contents for RT210W

Reviews:

Brands by name

Popular brands

Askey RT210W, User Manual

Search results

Summary of Contents for RT210W

Reviews:

Brands by name

Popular brands