Askey Computer WLC3030 User Manual Download Page 28

Page: 28 / 82

802.11b/g Wireless LAN Card User's Manual

Status Tab

The

Status

tab contains general information about the connection and activity of your current

connection. The following table describes the items found on the

Status

screen.

Screen Item

Description

Current Profile

Name of your current settings.

SSID

Displays the name of the wireless network your station is currently
connected to.

Network Mode

Infrastructure or Ad-Hoc (peer-to-peer).

Channel

Shows which channel is currently in use.

Tx Rate

Transmission rate at which data is transferred.

Privacy

WEP enabled or disabled.

Power Saving

Displays whether power consumption is enabled by the Wireless
LAN Card to extend the battery life of your notebook.

Sent

Number of packets sent.

Summary of Contents for WLC3030



















































































Search results

Summary of Contents for WLC3030

Reviews:

Related manuals for WLC3030

Brands by name

Popular brands

Askey Computer WLC3030, User Manual

Search results

Summary of Contents for WLC3030

Reviews:

Related manuals for WLC3030

Brands by name

Popular brands