Askey Computer RT410W 802.11 a Operation Manual Download Page 20 | Manualshive

Page: 20 / 24

background image

Clone MAC

If you want to connect to more than one PC through this Station, choose

Disabled

. Otherwise,

click

Enabled

.

Wireless LAN Mode

Choose one of the wireless LAN mode listed below as the wireless communication way.

802.11a:

The transmission speed is fast. Most countries support this function.

802.11a turbo: Faster than 802.11a, yet not all countries support this one.

802.11b:

If the frequency rate is up to 2.4G, please choose this one.

802.11g:

It supports the same speed with 802.11a. Yet it support different frequency rate

with 802.11a.

There are two ways to take the mode change effective.

Ø

After change the mode setting, unplug the power cord and re-plug it. Then restart the station.

Ø

After change the mode setting, go to

Wireless Setting Page

and click the

Reboot

button.

«
...
18
19
20
21
22
...
»

Summary of Contents for RT410W 802.11 a

























Reviews:

No comments

Related manuals for RT410W 802.11 a

Brand: Samsung Pages: 22

Brand: NEC Pages: 24

Brand: Da-Lite Pages: 8

Brand: TechniSat Pages: 8

Brand: Aiwa Pages: 20

Brand: Sennheiser Pages: 7

Brand: Walimex Pro Pages: 13

Brand: X2 Digital Wireless Systems Pages: 20

Brand: Aiwa Pages: 30

AMERICAN STARPOWER X2

Brand: Nady Systems Pages: 2

Brand: miniDSP Pages: 21

Impres PMLN5729

Brand: Motorola solutions Pages: 82

Brand: SONIQ Pages: 7

Microport SM 1008

Brand: Sennheiser Pages: 11

Brand: Magnavox Pages: 1

Brand: BestMedia Pages: 5

Brand: SOUNDMASTER Pages: 12

Brand: Neat Microphones Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands