manualshive.com logo in svg

Aruba AP-274, Installation Manual

Share
Download
Aruba AP-274 Installation Manual Download Page 10

10

AP-270 Series Outdoor Access Point

| Installation Guide

Figure 10  

Mounting Bracket (AP-270-MNT-V1) 

Figure 11  

Mounting Bracket (AP-270-MNT-V2) 

Mounting the AP to a Wall

1. Begin by marking the mounting points on the wall in the location you have selected.

a. Put the mounting bracket (included in the mount kit) on the installation position against the wall.

b. Using the mounting bracket as the template, mark four mounting points on the wall. 

2. Use a drill to create four holes on the four markings you created in the previous step.

3. Insert a anchor bolt into each drilled hole. Anchor bolts are not included in the mount kit.

4. Place the mounting bracket over the anchor bolts and press the bracket against the wall.

5. Place the washers and nut onto the bolt’s threaded end and tighten the nut till the mounting bracket is 

firmly attached to the wall as shown in 

Figure 12

 or 

Figure 13

.

Figure 12  

Attaching the Mounting Bracket (AP-270-MNT-V1) to a Wall 

To install 
AP

To install 
AP

Summary of Contents for AP-274


























Reviews:

No comments

Brands by name

Popular brands

Load more brands