Art's-Way Manufacturing 6520 Operator'S Manual Download | Manualshive

Page: 23 / 64

background image

OPERATION OF GRINDER MIXER

21

165 BU.

– APPROXIMATE CAPACITY CALIBRATION – IN POUNDS*

Actual weights may vary due to material, moisture, and screen size. Ration weight is not included and is
variable.

Window
Position

Ground Oats

22.5 lbs/bu

Ground Barley

36 lbs/bu

Ground Milo

56 lbs/bu

Ground Shelled

Corn 50 lbs/bu

Ground Ear

Corn 38 lbs/bu

Un-ground Shelled Corn 56

lbs/bu

Full

3777

6043

9400

8393

6378

9400

9

3554

5686

8845

7897

6002

8845

8

3302

5282

8217

7337

5576

8217

7

3047

4876

7585

6772

5147

7585

6

2768

4429

6890

6152

4676

6890

5

2528

4044

6291

5617

4269

6291

4

2287

3659

5692

5082

3862

5692

3

1985

3176

4941

4412

3353

4942

2

1744

2791

4342

3877

2947

4342

1

1504

2406

3743

3342

2540

3743

NOTE:

*

Above weights are approximate and are to be used as a guide only. Variations may occur due to

test weight of grain, slope of machine, moisture content, or screen size. For best ration control use an
electronic scale.

Table 3 - Approximate Calibration Capacity.

F

ILLING

T

HE

M

IXER

T

ANK

Make  sure  the  mixing  tank  unloading  door  is
closed.  As  the  mixing  tank  is  filling,  watch  the
ground  feed  through  the  mixing  tank  windows.  If
the top window is covered, this does not mean the
tank  is  full  as  the  mixing  auger  throws  material
away from the center of the tank. Continue loading
until  the  top  window  clears  (feed  drops)  and  then
becomes  covered  again  about  half-way  (see
Figure  24).  Stop  feeding  material  into  the
processor at this point, but continue operating until
the  processor  has  had  time  to  clear.

Do not

overload the mixer.

An overload can cause

damage to the machine. To estimate the number
of bushels that are in the tank, refer to Table 3.

Filling

Full

Figure 24 - Filling pattern

For the best mixing results, always add lightweight
bulky materials first. Always add high moisture

corn or grain last. Excessive amounts of wet or
bulky material may cause

bridging

in the mixing

tank.

S

PRING

L

OADED

T

ANK

L

ID

CAUTION:

DISENGAGE

ALL

THE

DRIVES.  SHUT  OFF  THE  TRACTOR
ENGINE  AND  PLACE  THE  KEY  IN
YOUR  POCKET  BEFORE  OPENING
THE MIXING TANK LID.

If the mixing tank is accidentally overfilled, it is
equipped with a spring loaded tank lid (see Figure
25). The lid also allows access to the inside of the
mixing tank. Keep the lid closed and latched at all
times.

CAUTION:  IF  ENTERING  THE  TANK,
MAKE SURE THE TRACTOR ENGINE IS
SHUT  OFF.  PLACE  THE  KEY  IN  YOUR
POCKET  AND  DISCONNECT  THE  PTO
DRIVELINE.

Figure 25 - Spring Loaded Tank Lid.

«
...
21
22
23
24
25
...
»

Summary of Contents for 6520

































































Reviews:

No comments

Related manuals for 6520

Brand: Far Tools Pages: 32

Brand: Protool Pages: 148

Brand: DeLonghi Pages: 26

Brand: YATO Pages: 84

5000 GGS Professional

Brand: Bosch Pages: 66

Brand: Milwaukee Pages: 8

Brand: Milwaukee Pages: 21

Brand: Milwaukee Pages: 33

Brand: Milwaukee Pages: 33

Brand: Milwaukee Pages: 67

HEAVY DUTY M18 ONEFSAG115XPDB

Brand: Milwaukee Pages: 82

Brand: Milwaukee Pages: 63

Brand: Milwaukee Pages: 163

Brand: Festool Pages: 126

Brand: Xtreme Polishing Systems Pages: 12

Brand: Hilti Pages: 84

Brand: Hercules Pages: 12

Brand: U.S.SAWS Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands