artisan TORO 3000 Instruction And Spare Parts Manual Download Page 3

Page: 3 / 16

artisan

TORO-3000 and TORO-4000

Extra Heavy Duty Cylinder Bed Lockstitch Compound

Needle Feed Walking Foot Stitching Machines.

CAUTION

…..

READ BEFORE OPERATING

THIS MACHINE...

Lubricate the Stitcher before operating!

Confirm you are plugging the electric motor

into the correct rated voltage.

Confirm the machine and motor are turning

over in a counter-clockwise rotation.

Your Artisan TORO machine is normally set up

with an SR-2 speed reducer/transmission to

controll your stitching speeds and to add

additional torque to drive the needle into heavy

leathers and fabrics at slow operating speeds.

5. After operating the machine for more than 25

days, if desired, the top stitching speed may

be increased to a maximum speed of 800 spm.

Keep your hands and all clothing away from

the machine when pushing the button to turn

the electric motor on.

Switch on the Servo Motor and check for the

LED light to illuminate.

Always switch off the motor when finished

sewing. Never leave the motor running

while away from the machine.

Always switch off the motor before changing

needles or adjusting the sewing machine.

10.

The machine is a fine tool, not a toy. Do not

let children operate the sewing machine.

SPECIFICATIONS

USAGE

Saddle Stitching, Tack, Shoes,
Boots, Saddle Bags, Harness.

Needle

Schmetz 794 D or 794 S for

Leather. For fabric 794

SEWING SPEEDS

Normal up to 600 spm.

Max. 800 spm.

Needle Diameter

# 110 to 250

# 18 to 27

STITCH LENGTH

0 to 11 mm

Thread

Z-69 to 415

# 00 to # 6 cord

PRESSER FOOT LIFT

By Hand Lifter 12 mm

By Foot Lifter 22 mm

Stitch Adjusting

Sliding Lever with Reverse

THREAD TAKE-UP

SYSTEM

Cam type thread take-up lever

Lubrication

Manual Lubrication with

Sewing Machine Oil

NEEDLE BAR

STROKE

56 mm

Motor

ESM-400 A

Electronic DC Servo.

30.

Summary of Contents for TORO 3000

















Search results

Summary of Contents for TORO 3000

Reviews:

Related manuals for TORO 3000

Brands by name

Popular brands

artisan TORO 3000, Instruction And Spare Parts Manual

Search results

Summary of Contents for TORO 3000

Reviews:

Related manuals for TORO 3000

Brands by name

Popular brands