background image

TR

OUBLESHOOTIN

G

TROUBLESHOOTING

PROBLEM

PROBLEM

SOLUTION

SOLUTION

Tubing Out *

1.  Tubing sensor indicator is not seated

2.  Ensure that the tubing sensor coupler  

    is seated completely

3.  Change the tubing

*    Return to Arthrex

®

 for repair

1.  Ensure that no tubing is connected to the  

    pump during power on sequence

*   Return to Arthrex for repair

1.  Check the AC main power cord

2.  Try an alternate power outlet

3.  Check the AC main fuses

*   Return to Arthrex for repair

1.  Activate LAVAGE mode

2.  Increase pressure

3.  Decrease outflow

1.  Check for error messages

2.  Open all tubing clamps and shut-off

    valves

3.  Ensure actual pressure is below the

     target pressure

4.  Check if the tubing is pinched, kinked,  

    or blocked

*    Return to Arthrex for repair
1.  Roller housing not secured – ensure  

    locking lever is properly secured

*    Return to Arthrex for repair

1.  Increase pressure

2.  Activate LAVAGE mode

3.  Reduce outflow

4.  Use high-flow cannulas

Console fails 

Self Diagnostic 

Test*

Console will  

not power up

Lack of  

distention liquid 

bloody/cloudy

Does not pump 

when activated

Door Open*

Inadequate 

pressure

No/Low Flow

1.  Check for error messages

2.  Check that all tubing clamps are open

3.  Check the settings for flow and pressure

4.  Check if the tubing is pinched, kinked  

    or blocked

5.  Check that tubing seats correctly over  

    the rollers

6.  Verify use of high-flow cannulas

7.  If failure remains, return to Arthrex  

    for repair

1.  If failure remains, increase or open outflow

2.  Manipulate joint to stress-free position

1.  Ensure adequate fluid supply

2.  Decrease outflow

3.  Check tubing for damage and if it is    

    pinched, kinked or blocked

4.  Check tubing for proper connections

5.  Replace tubing

6.  If failure remains, return to Arthrex  

    for repair

Synergy Shaver Detection

1.  Verify Synergy Resection Console is  

    at least 2.3

2.  Ensure the Synergy cable is connected

3.  Press stop and then run on CW4 while  

    the Synergy Resection Console is on

4.  Replace the shaver detection cable

5.  If failure remains, return to Arthrex  

    for repair

Overpressure

Pressure Fault

No Shaver  

Detection

For a full listing of warnings and instructions, please consult the Directions for Use and User Manual, packaged with the pump or 
pump tubing. These materials can also be found on Arthrex.com.

Summary of Contents for CONTINUOUS WAVE









Reviews: