manualshive.com logo in svg

ArtFox Pixel Blinder Bar, User Manual, Page: 2 / 14

Share
Download
ArtFox Pixel Blinder Bar User Manual Download Page 2

1A 

 

TABLE OF CONTENTS 

 
 

 

1.  Safety Instructions .......................................................................................................... 2 

2.  Technical Specifications .................................................................................................. 3 

3.  Accessories ..................................................................................................................... 4 

4.  Installation ...................................................................................................................... 4 

5.  How to set the unit ......................................................................................................... 5 

5.1 Control Panel ................................................................................................................ 5 

5.2  Main Functions .............................................................................................................. 6 

6.  How to control the unit .................................................................................................... 6 

6.1 Master/Slave Built-in Functions ..................................................................................... 7 

6.2 DMX  Controller .............................................................................................................8 

6.3 ArtNet ............................................................................................................................. 9 

6.4 DMX Channel ................................................................................................................ 9 

7.  Trouble shooting ............................................................................................................ 10 

8.  Fixture Cleaning ........................................................................................................... 10 

Summary of Contents for Pixel Blinder Bar















Reviews:

No comments