manualshive.com logo in svg

Artesyn Embedded Technology LGA50D JLP1J, User Manual

Share
Download
Artesyn Embedded Technology LGA50D JLP1J User Manual Download Page 18

 

LGA50D Evaluation Board User Manual 

 

 
Artesyn Embedded Technologies 

 

 

             LGA50D Evaluation Board 

                                                                                 

 

 

 December 2018

 

Page 18 of 18 

 
    

 

Contact for Technical Support and Information 

 

Americas 

Phone:

 

+1 888 412 7832 or  
+1 407 241 2752 

Email:

 

[email protected]

 

Availability:

 

8am to 8pm (EST) 

 

Asia 

Phone:

 

400 8899 130 (in China) and  
+86 29 88836505 (outside China) 

Email:

 

[email protected]

 

Availability:

 

8:30am to 5:30pm (HKT) 

 

Europe 

Phone:

 

(0) 8000 321 546 (in the UK) and  
+44 (0) 800 032 1546 (outside UK) 

Email:

 

[email protected]

 

Availability:

 

8am to 5pm (GMT) 

 

 
 
 
Visit us:  

http://www.artesyn.com/ 

http://www.artesyn.com/power/

 

 

Artesyn Embedded Technologies, Artesyn and the Artesyn Embedded Technologies logo are 
trademarks and service marks of Artesyn Embedded Technologies, Inc. All other names and logos 
referred to are trade names, trademarks, or registered trademarks of their respective owners. © 

2019 Artesyn

 Embedded Technologies, Inc. All rights reserved. For full legal terms and conditions, 

please visit 

www.artesyn.com/legal

. 

 

Summary of Contents for LGA50D JLP1J



















Reviews:

No comments

Brands by name

Popular brands

Load more brands