manualshive.com logo in svg

Artesyn Embedded Technology LGA50D JLP1J, User Manual

Share
Download
Artesyn Embedded Technology LGA50D JLP1J User Manual Download Page 14

 

LGA50D Evaluation Board User Manual 

 

 
Artesyn Embedded Technologies 

 

 

             LGA50D Evaluation Board 

                                                                                 

 

 

 December 2018

 

Page 14 of 18 

 
    

 

2.

 

Ripple and regulation measurement locations 

There are 3 test points provided to give accurate measurements of the output noise 
and ripple from the LGA50D. 

The mating connector to the SMA connector found on the Evaluation board can be 
defined as 

“A Straight Cable Mount SMA Connector, Plug, Crimp Termination type 

RG174U”. 

•

 

J1403 

–

 Point of Measurement for Vout-3 ripple.

 

•

 

J1401 

–

 Point of Measurement for Vout-3 regulation.

 

 

Fig. 12– Ripple and regulation measurement point for Vout-3 

•

 

J303 - Point of Measurement for Vout-2 ripple 

 

•

 

J301 - Point of Measurement for Vout-2 regulation

 

 

Fig. 13– Ripple and regulation measurement point for Vout-2 

Summary of Contents for LGA50D JLP1J



















Reviews:

No comments

Brands by name

Popular brands

Load more brands