background image

Install a 

left roof panel 

at the left

rear and right front corner of the roof.
Install a 

right roof panel

 at the left

front corner of the roof.

Install 4 

roof panels 

in the se-

quence and positions shown on pre-
vious page. 

Do not fasten the lower

end of the panels to the side wall
angles at this time. Continue weather
stripping the ridge opening.  Fasten
roof panel overlaps not used for ridge
cap (roof center).  Cover the head of
bolt with the 2" (5cm) piece of weather
stripping tape.

NOTE

Narrow roof panel crimped rib is

overlapped by wide rib of

adjacent panel where possible.

Step 14

I27

 Parts Needed For 

Roof Assembly

27

 8469 Left Roof Panel (2)

 6529 Roof Panel (4)

 8468 Right Roof Panel (1)

Cut 2 short 2" (5cm) strips off the

roll of 

weather stripping tape, 

and

put them aside. Cover the joint at the
peak with weather stripping tape.
Unroll the tape and press it down
over the opening at the ridge as you
install each roof panel. Do not cut the
tape at this time.

NOTE

If roof beam holes do not line up

with the roof panel holes, shift the

building from left to right.

If this does not help, your building

may not be level. Shim the

corners until holes line up.

FRONT

Do not fasten

at this time

Cut

Weather Stripping

and Fold Under

FRONT

Fasten At

Overlap with

Bolt

6529 Roof Panel

Fasten At

Overlap with

Bolt

Screws To

Roof Beam

Weather Stripping

Tape Roll

8469 Left Roof Panel

STEP

2

STEP

Strips

STEP

Screws To

Roof Beam

8468 Right

 Roof Panel

1

3

Summary of Contents for HM10667

































Reviews: