Arrow EH86-A Owner'S Manual & Assembly Instructions Download

Page: 31 / 32

Step 18

P31

●

Parts Needed For

●

Door Installation & Adjustment

●

Right Door Assembly (1)

●

Left Door Assembly (1)

From inside the building, put the

bottom of the right door assembly (on
your left when you are inside the
building) behind door jamb into the
front frame track.

Position the top of the door so that

the holes in the door line up with the
holes in the door slides.

Fasten the door to the door slides

using two #10Bx1/2" (13 mm) screws
per door slide.

NOTE

The holes in the door slides allow

you to adjust the doors. Place the

door in the middle holes.

Repeat steps 1 through 3 for the

left door.

Keep this Owner's Manual and Assembly Instructions for future reference.

STEP

Horizontal Door Brace

STEP

Gable

STEP

#10Bx1/2" (13 mm)
Screw

Door Slide

Adjustment Holes

Adjustment Holes Allow

Doors to Meet Evenly

Along Their Length

Right
Door

Left
Door

STEP

Front Floor Frame Assembly

Door Track

Door Slide

Door

Summary of Contents for EH86-A

































Search results

Summary of Contents for EH86-A

Reviews:

Related manuals for EH86-A

Brands by name

Popular brands

Arrow EH86-A, Owner'S Manual & Assembly Instructions

Search results

Summary of Contents for EH86-A

Reviews:

Related manuals for EH86-A

Brands by name

Popular brands