background image

The gables go on top of the front and
rear walls to support the roof beams.
The gables are packed nested to-
gether and might be mistaken as 1
piece.  Carefully separate them be-
fore continuing.

Position  mid and outer gable

braces on right  and  left gables.
Short mounting flange of brace must
face center of gable.  Fasten using
#10-32x7/16" bolts, washers and
square nuts.  Assemble 2 sets of
gables.

Step 2

BW15

 Parts Needed For 

Gables All Sizes

 6381 Mid Gable Brace (4)

 6380 Outer Gable Brace (4)

 7942 Right Gable (2)

 7943 Left Gable (2)

15

7912

#10-32 Square Nut

#10-32x7/16" Bolt

10462

Short Mounting Flange

Must Face Towards

Center of Gable

Step 3

 Parts Needed For 

Roof Beam Assemblies

 10462 Roof Beam (2) (All Sizes)

 7912 Roof Beam (2) (1217)

 7912 Roof Beam (4) (1224)

 7912 Roof Beam (6) (1231)

The roof beams join the gables to the
truss and supports the roof panels.

1

Align the holes on 2 roof beams,

back-to-back and fasten using 4 #10-
32x7/16" bolts and square nuts.

Small Holes

on Top

7942

7943

6380

6381

#10-32x7/16" Bolt

#10-32 Square Nut

Washer

FRONT

Assembled

End
View

Summary of Contents for 697.68608-A












































Reviews: