Arrow 17 00515 01 Hardware Referance Manual Download Page 10 | Manualshive

Page: 10 / 72

background image

Hardware Reference Manual

Version 1.0

- 11 -

eInfochips Confidential

3

Preface

This document provides an overview of the ERAGON660 SBC and development kit based on the
Qualcomm Snapdragon™ 660. It provides step-by-step information about hardware components and
associated software release Android 8.1.0 (Oreo).

Intended Audience

This document is intended to be used by for technically qualified personnel. It is not intended for general
audiences.

Intended Use

The development platform supports a wide range of industry interfaces and offers a comprehensive
hardware and software design. It comes with Android software packages. This platform enables
developers to evaluate and create solutions targeted at various market segments while customers and
OEMs can build their products based on these designs directly or with customizations.

«
...
8
9
10
11
12
...
»

Summary of Contents for 17 00515 01









































































Reviews:

No comments

Related manuals for 17 00515 01

Brand: IBASE Technology Pages: 65

Brand: Supero Pages: 107

Brand: Texas Instruments Pages: 16

Brand: Biostar Pages: 65

Brand: Gigabyte Pages: 31

Brand: Gigabyte Pages: 44

TLE986 Evalboard Series

Brand: Infineon Pages: 20

Brand: MSI Pages: 32

Brand: Avalue Technology Pages: 60

Brand: Mercury Pages: 42

Brand: Texas Instruments Pages: 13

Brand: Microchip Technology Pages: 18

Brand: Yamaha Pages: 124

Brand: Yamaha Pages: 122

Brand: Yamaha Pages: 90

Brand: DFI Pages: 93

CY8CPROTO-064B0S3

Brand: Cypress Pages: 47

Brand: DFI Pages: 134

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands