background image

ACCESSORIES....

     A6 WEB

6

* Some drilling required to fit buildings without mid-wall bracing.

Model No. SS404
•  Makes 8" to 12" (20-30cm)
   wide shelves in any length.
•  Brackets, braces,
   hardware included.
   Lumber is not included.

Model No. SS900-A
•  Grey color
•  3 shelves
•  Holds up to 85 lbs. (38kg)
   (even weight distribution)

Heavy-duty, galvanized steel shelf units help organize storage
space. They easily mount on the wall or sit on the floor. Fits all
Arrow buildings.*

SHELF UNITS

Must be drilled for use as workbench in Estator.
+ Even weight distribution.

10' Long, 250 lb. (113kg) load+

Fits all Arrow 10' wide buildings.

16 lbs. (7kg)

AT101

Model No.

Fits

Shipping Weight

ATTIC KIT / WORKBENCH KIT

Heavy-duty galvanized steel bars that
fit all 10' wide Arrow buildings. They
install quickly and easily to help
organize space and create more
useable space as an attic or
workbench. Will hold up to 250 lbs.
(113kg) evenly distributed.

Model No. AK100

New concrete anchor system permits
anchoring any size Arrow building
directly to a concrete slab. Each kit
contains heavy-duty, hot-dipped
galvanized steel corner gussets and
perimeter clips which fit over the floor
frame and lag bolt into a concrete slab.
Full assembly instructions and a 1/4"
masonary drill bit are included.

TOOL HANGING RACK

Model No. TH100

The perfect tool organizer. Twin
25 1/2" (65cm) steel channels
plus five heavy-duty snap-in
hangers and a small tool holder for
screwdrivers, pliers, etc. Holders
slide along channel for fully
adjustable spacing. Great for
garage, basement, or the back
of any door. Fits all Arrow
storage buildings.

ROOF STRENGTHENING

(heavy snow load) KITS

Extra roof beams and gable braces
designed for added protection against
heavy snow accumulation. Increases
the strength of your roof by 50%.

ANCHOR KITS

Model No. AK4

Anchor Kit contains heavy-duty steel
augers, 60' (18m) of steel cable and 4 cable
clamps. No digging or concrete
pouring, just insert cable under roof,
over roof beams, into augers and twist
augers into the ground. For buildings
larger than 10'x9', use 2 kits.

FLOOR FRAME KITS

MODELS FB47410, FB5465, FB106-A

FB109-A and FB1014-A

A simple new floor frame system made of heavy-duty, hot-dipped
galvanized steel.  Use as foundation for plywood, sand or stone.

Model No. AK600

Earth Anchor Kit anchors any size
Arrow building to the ground.
Each kit contains heavy duty,
hot-dipped galvanized steel
corner gussets and 4 earth anchors.

Summary of Contents for VM108

































Reviews: