Arrow Storage Products DKGA-A Owner'S Manual And Assembly Manual Download Page 23

Page: 23 / 32

23AG

Step 9: Continued

Holes in Door Brace must line up

with holes in Door Panel.

Position

Horizontal Door Braces,

and

Vertical Door Brace (Hinge)

and

Vertical Door Brace (Latch)

as shown.

NOTE: Doors

in the image below are shown

pictured from the inside of the building. Pay close

attention to how parts are positioned. Make sure

hinge holes in the

Vertical Door Brace (Hinge)

line up with hinge holes in

Door Panel (Hinge)

10635

10637

10678

Horiz. Door

Brace

10635

Vert. Door

Brace (Hinge)

10637

Vert. Door

Brace (Latch)

10678

10623

80051

10624

Inside

You will need for this page:

[ NO HARDWARE NEEDED

FOR THIS STEP ]

Inside

Right Door

Left Door

10678

Extra hole along

INSIDE of Door.

10635

Three (3) holes along

INSIDE of Door.

Summary of Contents for DKGA-A

































Search results

Summary of Contents for DKGA-A

Reviews:

Related manuals for DKGA-A

Brands by name

Popular brands

Arrow Storage Products DKGA-A, Owner'S Manual And Assembly Manual

Search results

Summary of Contents for DKGA-A

Reviews:

Related manuals for DKGA-A

Brands by name

Popular brands