manualshive.com logo in svg

Armitage Shanks Sensorflow A4126AA, Installation Instructions Manual

Share
Download
Armitage Shanks Sensorflow A4126AA Installation Instructions Manual Download Page 6

6

5 

INSTALLATION GUIDE

DO NOT

 apply heat near this product. Heat generated by soldering 

could damage plastic parts and seals.

5.1 

Mounting

Before connection, flush water through pipe-work to 

remove all debris etc. to prevent damage to the valve 

mechanism.
THEN ENSURE WATER SUPPLIES HAVE BEEN 

ISOLATED.

2.

 Fit the two rubber mouldings onto the metal fixing plates. Then from behind the panel slide the fixing 

plate assemblies onto the fixing studs as shown.

3.

 Hand tighten the nuts against the fixing plates until the rubber mouldings make contact with the rear 

of the panel. Ensure the spout & sensor are positioned correctly, & then tighten the nuts securely with 

a 13mm A/F spanner.

CABLE COLOURS:

The cables emerging from the spout are connected to the integral sensor.

BLACK & RED cables will connect to the solenoid valve.

GREY cable will connect onto the PCB inside the PSU

Do not cut these cables

.

DRILL PANEL 

HOLE Ø25 

& Ø30

1

1

2

3

13

INSTALLATION HEIGHT: we recommend the spout outlet be positioned approximately 150-200mm 

above the basin or worktop (which ever is higher). Greater height may cause users to splash water out-

side the basin whereas lower height may affect activity space. Consideration should also be give to the 

overall aesthetical appearance. Installations vary significantly, so use this dimension as a guideline only.

1.

 Screw the copper inlet pipe into the spout, 

trim to length if necessary. Ensure the foam 

gaskets are in place as shown. These gaskets 

should already be fitted into the recess at the 

rear of the spout & sensor (self adhesive). The 

M8 fixing studs should also be pre-fitted. Offer 

the spout towards the upper hole in the panel.

Mark the position of the spout onto the panel at 

the preferred location & drill a hole Ø30. Mark the 

position of the sensor onto the panel approximately 

80 to 90mm below the spout centre line. Drill a 

hole Ø20. Upper hole is for the spout fixing stud & 

inlet pipe. Lower hole is for the sensor fixing stud & 

cables. Ensure the holes remain within the areas 

sealed by the foam gaskets.

Feed the inlet pipe & fixing stud through the 

panel hole. Push the spout against the panel & 

ensure the foam gasket makes contact. Simi-

larly offer the sensor towards the lower panel 

hole, push the fixing stud & cables through & 

park it against the panel.

Summary of Contents for Sensorflow A4126AA





















Reviews:

No comments

Brands by name

Popular brands

Load more brands