manualshive.com logo in svg

Armitage Shanks A4125AA, Installation Instructions Manual

Share
Download
Armitage Shanks A4125AA Installation Instructions Manual Download Page 14

14

INSTALLATION GUIDE continued…

Electrical connection continued…

Sensor taps stickers:

 To complete the installation, 2 stickers are 

provided which can be stuck onto a wall or panel in close proximity to 

this product to advise the end user that this product sensor operated.

6 

TAP OPERATION

Sensorflow 21 products use an Infrared Sensor to activate the system.

The sensor is triggered by something reflective (normally hand movement) 

in the Sensing Region.

Move hands towards the spout:

Water will flow.

Move hands away from the spout: 

Water will continue to flow for a 

second or two, and then turn off.

Sensor is factory set to 

Proximity

Mode

, & is designed to trigger the

water flow 

only when a hand (or similar) 

is in the Sensing Region –

 just 

in front of the sensor / outlet.

For this range of products, the sensor 

is located near the base of the spout 

and faces forwards

Example above of an installation where PSUs are all mains versions.

145

www.divapor.com

Summary of Contents for A4125AA





















Reviews:

No comments

Brands by name

Popular brands

Load more brands