manualshive.com logo in svg

Armitage Shanks A4122AA, Installation Instructions Manual

Share
Download
Armitage Shanks A4122AA Installation Instructions Manual Download Page 1

Important:

1. Electrical connection:  

mains electric powered version of this 

     product must be connected to a continuous permanent power supply.

   

2. Sensor protector:  

this black-out lens cover should only be removed from

    the sensor after completing installation & at least 20 seconds after powering up.

See page 3 for more details.

Sensorflow 21 standard & compact basin

spouts A4122AA, A4171AA, A4172AA,

A4664AA, A4798AA & A4799AA

INSTALLER:

  

After installation please pass this instruction booklet to user

IMPORTANT

BEFORE CONNECTION, FLUSH WATER THROUGH PIPEWORK TO REMOVE

ALL DEBRIS ETC. WHICH COULD DAMAGE THE VALVE MECHANISM

INSTALLATION 

INSTRUCTIONS

Ø15

Ø15

67

40

61

103

86

116

Ø15

Ø15

Ø57

Ø35

112

Standard 166 Compact 136

Standard 104 Compact 74

260

35 max.

750

Ø10

15°

Note: 
Standard spouts
are 30mm taller than
the compact versions.

Summary of Contents for A4122AA





















Reviews:

No comments

Brands by name

Popular brands

Load more brands