ARM Musca-S1 Technical Reference Manual Download Page 113

Page: 113 / 194

3.9

PVT sensor registers

The Musca

‑

S1 test chip implements registers that monitor the

Process, Voltage, Temperature

(PVT)

sensor system.

This section contains the following subsection:
•

3.9.1 PVT sensor control registers summary

on page 3-113

3.9.1

PVT sensor control registers summary

The PVT sensor control registers are mapped to both the Non

‑

secure and Secure Expansion 1 regions.

The base memory addresses of the PVT sensor control registers are:
•

0x4010_9000

in the Non

‑

secure region.

•

0x5010_9000

in the Secure region.

The following table shows the PVT sensor control registers in address offset order from the base memory
address. Undefined registers are reserved. Software must not attempt to access these registers.

Table 3-51 PVT sensor control registers summary

Offset

Name

Type Reset

Width Description

0x0000

CTRL_REF_CNTR

0x0000_0000

See

CTRL_REF_COUNTER Register

on page 3-113

0x0004

CRTL_ENABLE

0x0000_0000

See

CTRL_ENABLE Register

on page 3-115

0x0008

CTRL_AUTOCLEAR RW

0xFFFF_FFFF

See

CTRL_AUTOCLEAR Register

on page 3-115

0x000C

CTRL_CLKSEL

0x0000_0000

See

CTRL_CLKSEL Register

on page 3-115

0x0010

CTRL_SAMPLE

0x0000_0000

See

CTRL_SAMPLE Register

on page 3-116

0x0014

CTRL_PERIOD

0x0000_00FF

See

CTRL_PERIOD Register

on page 3-116

0x0018

OVERFLOW-STATUS RO

0x0000_0000

See

OVERFLOW_STATUS Register

on page 3-117

0x001C

INTR_STATUS

0x0000_0000

See

INTR_STATUS Register

on page 3-117

0x0020

CLEARED_STATUS

0x0000_0000

See

CLEARED_STATUS Register

on page 3-118

0x0024

SAMPLED_STATUS

0x0000_0000

See

SAMPLED_STATUS Register

on page 3-118

0x0028

COUNTER_STATUS

0x0000_0000

See

COUNTER_STATUS Register

on page 3-119

0x0080

SENSOR0_VAL

0x0000_0001

See

SENSOR0_VAL Register

on page 3-119

0x0084

SENSOR1_VAL

0x0000_0000

See

SENSOR1_VAL Register

on page 3-119

0x0088

SENSOR2_VAL

0x0000_0000

See

SENSOR2_VAL Register

on page 3-120

CTRL_REF_COUNTER Register

The CTRL_REF_COUNTER Register characteristics are:

Purpose

Controls the PVT sensors reference counter.

Usage constraints

There are no usage constraints.

3 Programmers model

3.9 PVT sensor registers

101835_0000_01_en

reserved.

3-113

Non-Confidential

Summary of Contents for Musca-S1


































































































































































































Search results

Summary of Contents for Musca-S1

Reviews:

Related manuals for Musca-S1

Brands by name

Popular brands

ARM Musca-S1, Technical Reference Manual

Search results

Summary of Contents for Musca-S1

Reviews:

Related manuals for Musca-S1

Brands by name

Popular brands