ARM Cortex-R4 Technical Reference Manual Download

Page: 167 / 436

Events and Performance Monitor

ARM DDI 0363G

6-11

ID073015

Non-Confidential

6.3.4

c9, Overflow Flag Status Register

The PMOVSR Register characteristics are:

Purpose

Indicates if event counters have overflowed. All overflow flags are reset
to zero.

Usage constraints

The PMOVSR Register is accessible in:
•

Privileged mode

•

User mode only when the PMUSERENR.EN bit is set to 1, see

c9,

User Enable Register

on page 6-15

Configurations

Available in all processor configurations.

Attributes

See

Table 6-5

Figure 6-4

shows the PMOVSR bit assignments.

Figure 6-4 PMOVSR Register bit assignments

Table 6-5

shows the PMOVSR bit assignments.

To access the PMOVSR, read or write CP15 with:

MRC p15, 0, <Rd>, c9, c12, 3 ; Read PMOVSR
MCR p15, 0, <Rd>, c9, c12, 3 ; Write PMOVSR

If an overflow flag is set to 1 in the PMOVSR it remains set until one of the following happens:
•

writing 1 to the flag bit in the PMOVSR clears the flag

•

the processor is reset.

The following operations do

not

clear the overflow flags:

•

disabling the overflowed counter in the PMCNTENCLR Register

•

disabling all counters in the PMCR Register

•

resetting the overflowed counter using the PMCR Register.

3 2 1 0

Reserved

Performance monitor counters

overflow flags

Cycle count overflow

Table 6-5 PMOVSR Register bit assignments

Bits

Name

Function

[31]

Cycle counter overflow

Cycle counter overflow flag

[30:3]

UNP on reads, SBZP on writes

[2]

Counter 2 overflow flag

[1]

Counter 1 overflow flag

[0]

Counter 0 overflow flag

Summary of Contents for Cortex-R4


















































































































































































































































































































































































































































Search results

Summary of Contents for Cortex-R4

Reviews:

Related manuals for Cortex-R4

Brands by name

Popular brands

ARM Cortex-R4, Technical Reference Manual

Search results

Summary of Contents for Cortex-R4

Reviews:

Related manuals for Cortex-R4

Brands by name

Popular brands