ARM ARM946E-S Technical Reference Manual Download Page 59 | Manualshive

Page: 59 / 189

background image

Caches

Copyright © ARM Limited 2000. All rights reserved.

3-5

For example, the access address is broken down as shown in Figure 3-2 for a 4Kbyte
cache.

Figure 3-2 Access address for a 4KB cache

Three additional bits are associated with each TAG entry:

Valid bit

This is set when the cache line has been written with valid data.
Only a valid line can return a hit during a cache lookup. On reset,
all the valid bits are cleared.

Dirty bits

These are associated with write operations in the DCache and are
used to indicate that a cache line contains data that differs from
data stored at the address in external memory.

Data can only be marked as dirty if it resides in a write back
protection region.

256KB

Addr[15:5]

Addr[31:16]

512KB

Addr[16:5]

Addr[31:17]

1MB

Addr[17:5]

Addr[31:18]

Table 3-1 TAG and index fields for supported cache sizes (continued)

Cache size

Index

TAG

31

10 9

5 4

2 1 0

TAG

Index

Word Byte

«
...
57
58
59
60
61
...
»

Summary of Contents for ARM946E-S






























































































































































































Reviews:

No comments

Related manuals for ARM946E-S

Brand: Data Translation Pages: 98

Brand: MiLAN Pages: 1

PacketShaper PS-S200

Brand: Symantec Pages: 2

Brand: 3Com Pages: 18

Brand: Supermicro Pages: 24

Brand: u-blox Pages: 29

Brand: Lanner Pages: 78

Brand: Z3 Technology Pages: 87

Brand: Sangoma Pages: 6

Brand: PMD Pages: 74

DataPlot CB1224

Brand: B-G Instruments Pages: 4

Brand: Aaeon Pages: 72

Brand: National Instruments Pages: 121

Brand: Mod Pages: 11

Brand: Netequalizer Pages: 14

Brand: Data Translation Pages: 62

Brand: Intellinet Pages: 32

Brand: Spectrum Digital Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands