Arkray Glucocard Shine Page 39 User Manual Download

Page: 39 / 50

www.arkrayusa.com

• We have validated

Clorox Germicidal Wipes

with 0.55%

sodium hypochlorite as the active ingredient for disinfecting

the GLUCOCARD Shine Meter and lancing device. It has been

shown to be safe for use with the meter and lancing device.

This disinfectant is available commercially in towelette form. In

addition to GLUCOCARD Shine BGMS instruction,

please read

the instructions provided by the manufacturer of Clorox

Germicidal Wipes before using it

Note:

The disinfectant products can be purchased online retailers

(e.g. Amazon) or by telephone at the manufacturer. To find out

where to purchase the disinfectant product, please contact the

manufacturer or visit their website as listed above.

Name

Manufacturer

EPA registration

number
Active
ingredients

Clorox® Germicidal Wipes

Clorox Professional Products Company

[Phone] 1 800 537 1415
[Website] www.cloroxprofessional.com

67619-12

Sodium Hypochlorite: 0.55%

Pre-cleaning and Disinfection Procedures:

Open the cap of the Clorox

Germicidal Wipes container

and pull out 1 towelette

and close the cap.

Summary of Contents for Glucocard Shine



















































Search results

Summary of Contents for Glucocard Shine

Reviews:

Related manuals for Glucocard Shine

Brands by name

Popular brands

Arkray Glucocard Shine, User Manual

Search results

Summary of Contents for Glucocard Shine

Reviews:

Related manuals for Glucocard Shine

Brands by name

Popular brands