background image

 

 SERIES

-

 

 

 

-

6

-

Technical Data 

 
 
 

Standard Features

 

• 

Minimum operating pressure: 

2 bar (29 psi) 

• 

Maximum operating pressure: 

10 bar (145 psi) 

• 

Clean filter pressure loss: 

0.1 bar (1.45 psi) 

• 

Maximum water temperature: 65°C (149°F) 

• 

Filtration 

range: 

  50-400 

micron 

• 

Control voltage:   

 

12V DC, 24V DC 

• 

Flush water consumption (at minimum working pressure): 7 liters (2.11 gallons) 

• 

Filter housing materials: carbon steel coated with baked on epoxy 

• 

Available connections:  M = Threaded socket    V = Vic.    F = Flange 

 

 
 

General Technical Data 

Model 

Number 

Conn. 

Size ØD 

Screen 

Area 

* Max. Flow 

Rate 

** Flushing 

Flow Rate 

ØD1 X  Y  H Weight 

 (inch) 

(cm

2

)

 

(m

3

/h) (m

3

/h) (inch) (mm) (mm) (mm) (Kg) 

AK 

B2 

2 1100  30 

10 177 174 480 24 

AK 

B2-S  2 1630  30 

10 177 174 625 26 

AK 

B3 

3 1100  40 

10 192 188 495 25 

AK 

B3-S  3 1630  50 

10 192 188 640 27 

AK 

B4 

4 1630  80 

10 220 210 650 28 

 

= Compact

       S 

= Filter with large filtration area 

* Flow rate data are for high quality water at filtration grade of 120 micron. 

** Flushing flow rate data are for minimum operational pressure (2 bar / 29 psi). 

 
 
 
 

Filtration Grade Conversion Table

 

Micron  50  80  100 120 150 200 400 

Mesh  300 200 150 120 100  80  40 

 

 

Summary of Contents for B Series



































Reviews: