background image

947

867 ± 5

Ø76

550

560

 PELLET STOVE KMP MYSINGE

ARITERM SWEDEN AB

 

  

Installation Instructions - 

2010.05.20 - 7

/24

  1.3 Technical data

Heating output max ....................................... approximately 6 kW
Heating output min .....................................approximately 3.5 kW
Pellet hopper ....................................38 litres (approx 20 - 25 kg*) 
Efficiency level ........................................................... approx 93%
Smoke temperature ........................................................... <200˚C
Temperature range thermostat .............................approx 10 - 30˚C
Weight ..................................................................... 100 - 138 kg
Electrical connection .................................................. 230 V 50 Hz
Electrical output (firing) ....................................................... 450 W
Electrical output (operation) .................................................. 40 W
Fuel  wood pellets Ø6 or 8 mm, class 1 according to Swedish standard.
* Depending on fuel density.

Fig. 3

  1.4  Control panel

The control panel has a display and adjustment dial (see fig. 3):
-  The display shows the operating mode and the current temperature.  
  Explanatory text scrolls through the display every 5 seconds.
-  The adjustment dial is used by pressing or turning.  
   

-  Turn to scroll through the menu or change the value when adjusting.

   

-  Pushing once makes a selection in the menu. 

Example:
Connect the stove to the wall socket. Pressing once causes the panel to ask “Start?”.  
Pressing again means that you confirm the question and the stove starts. 
If you turn clockwise instead you come to “Stop T”,“UserMenu” and “Back”.
Stop T:  

Press to adjust stop temperature..

Usermenu: 

Press to adjust time and temperature settings.

Back:   

Press to return to the starting point.

The stove is started by pressing the control panel dial and confirming. “Start?”  
by pressing again. Take care not to start the stove when there  
are flammable objects above or immediately adjacent!
To shut off, press the control panel dial and confirm “Stop?” by pressing once.
Other menu steps are shown in section 1.6.

Summary of Contents for MYSINGE

























Reviews: